Máy hiện sóng Tektronix TDS3054C (500MHz, 4 kênh)

Hãng sản xuất: TEKTRONIX
Model: TDS3054C
Xuất xứ: China (Trung Quốc)
- Yêu cầu báo giá
Liên hệ
- Thêm vào giỏ hàng
- Mua ngay
Tham khảo dịch vụ Hiệu chuẩn-Kiểm định và Sửa chữa
Gọi để có giá tốt
TP. Hà Nội: (024) 35.381.269
TP. Đà Nẵng: (023) 63.747.711
TP. Bắc Ninh: (0222)730.39.68
TP. HCM: (028) 38.119.636

Thông số kỹ thuật
Thông tin hãng sản xuất

Băng thông : 500Mhz
Số kênh : 4
Rise time : 0.7ns
Tốc độ lấy mẫu : 5Gs/s mỗi kênh
Giới hạn băng thông : 20 Mhz, 150Mhz
Kiểu đầu vào : AC, DC, GND
Trở kháng vào : 1 MΩ và 50 Ω
Độ nhạy điện áp : 1 mV/div ~ 10 V/div (1 MΩ), 1 mV/div ~ 1 V/div
(50 Ω)
Độ phân giải : 9 bit
Điện áp lớn nhất đầu vào : 150 VRMS (1 MΩ) và 5 VRMS (50Ω)
Độ chính xác DC khuếch đại : ±2%
Thời gian quét : 1ns ~ 10s
Độ chính xác thời gian : ±20 ppm
Chế độ kích : Auto (supports Roll Mode for 40 ms/div and slower), Normal, Single Sequence

Màn hình : 6.5 inch, TFT
Độ phân giải màn hình : 640x480 pixel
Cổng kết nối : RJ-45, USB2.0, GPIB (option TDS3GV), RS-232C, VGA (option TDS3GV)
Nguồn cung cấp : 100 VRMS to 240 VRMS ±10%
Phụ kiện kèm theo : Máy chính, Que đo x 4, HDSD, chứng nhận chuẩn hãng.

Chi tiết

TDS3000C Series Electrical Characteristics

Characteristic	TDS3012C	TDS3014C	TDS3032C	TDS3034C	TDS3052C	TDS3054C
Bandwidth	100 MHz	100 MHz	300 MHz	300 MHz	500 MHz	500 MHz
Calculated Rise Time (typical)	3.5 ns	3.5 ns	1.2 ns	1.2 ns	0.7 ns	0.7 ns
Input Channels	2	4	2	4	2	4
External Trigger Input	Included on all models
Sample Rate on each channel	1.25 GS/s	1.25 GS/s	2.5 GS/s	2.5 GS/s	5 GS/s	5 GS/s
Record Length	10 kpoints
Vertical Resolution	9 bits
Vertical Sensitivity, 1 MΩ	1 mV/div to 10 V/div
Vertical Sensitivity, 50 Ω	1 mV/div to 1 V/div
Input Coupling	AC, DC, GND
Input Impedance	1 MΩ in parallel with 13 pF or 50 Ω
DC Gain Accuracy	±2%
Maximum Input Voltage, 1 MΩ	150 V_RMS with peaks at ≤400 V
Maximum Input Voltage, 50 Ω	5 V_RMS with peaks at ≤30 V
Position Range	±5 div
Bandwidth Limit	20 MHz	20 MHz	20 MHz, 150 MHz	20 MHz, 150 MHz	20 MHz, 150 MHz	20 MHz, 150 MHz
Time Base Range	4 ns to 10 s	4 ns to 10 s	2 ns to 10 s	2 ns to 10 s	1 ns to 10 s	1 ns to 10 s
Time Base Accuracy	±20 ppm over any 1 ms time interval
Input/Output Interfaces
Ethernet Port	RJ-45 connector, supports 10Base-T LAN
USB Port	Front-panel USB 2.0 host port Supports USB flash drive
GPIB Port	Full talk/listen modes, setting and measurements (Optional with TDS3GV Communications Module)
RS-232-C Port	DB-9 male connector, full talk/listen modes; control of all modes, settings and measurements Baud rates up to 38,400 (Optional with TDS3GV Communications Module)
VGA Video Port	DB-15 female connector, monitor output for direct display on large VGA-equipped monitors (Optional with TDS3GV Communications Module)
External Trigger Input	BNC connector, input impedance >1 MΩ in parallel with 17 pF; max input voltage is 150 V_RMS

Acquisition Modes

Mode	Description
DPO	Captures and displays complex waveforms, random events and subtle patterns in actual signal behavior. DPOs provide 3 dimensions of signal information in real time: Amplitude, time, and the distribution of amplitude over time
Peak Detect	High-frequency and random glitch capture. Captures glitches as narrow as 1 ns (typical) using acquisition hardware at all time base settings
WaveAlert^®	Monitors the incoming signals on all channels and alerts the user to any waveform that deviates from the normal waveform being acquired
Sample	Sample data only
Average	Waveform averaged, selectable from 2 to 512
Envelope	Min-max values acquired over one or more acquisitions
Single Sequence	Use the Single Sequence button to capture a single triggered acquisition sequence at a time

Trigger System

Characteristic	Description
Main Trigger Modes	Auto (supports Roll Mode for 40 ms/div and slower), Normal, Single Sequence
B Trigger	Trigger after time or events
Trigger After Time Range	13.2 ns to 50 s
Trigger After Events Range	1 to 9,999,999 events

Trigger Types

Trigger	Description
Edge	Conventional level-driven trigger. Positive or negative slope on any channel. Coupling selections: AC, DC, Noise Reject, HF Reject, LF Reject
Video	Trigger on all lines or individual lines, odd/even or all fields on NTSC, PAL, SECAM
Extended Video	Trigger on specific lines in broadcast and non-broadcast (custom) standards and on analog HDTV formats (1080i, 1080p, 720p, 480p). Requires TDS3VID or TDS3SDI application module
Pulse Width (or Glitch)	Trigger on a pulse width <, >, =, ≠ to a selectable time limit ranging from 39.6 ns to 50 s
Runt	Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again
Slew Rate	Trigger on pulse edge rates that are either faster or slower than a set rate. Edges can be rising, falling, or either
Pattern	Specifies AND, OR, NAND, NOR when true or false for a specific time
State	Any logic state. Triggerable on rising or falling edge of a clock. Logic triggers can be used on combinations of 2 inputs (not 4)
Comm	Provides isolated pulse triggering required to perform DS1/DS3 telecommunications mask testing per ANSI T1.102 standard. Requires TDS3TMT application module
Alternate	Sequentially uses each active channel as a trigger source

Waveform Measurements

Characteristic	Description
Cursors	Amplitude, Time
Automatic Measurements	Display any four measurements from any combination of waveforms. Or display all measurements with measurement snapshot feature. Measurements include Period, Frequency, +Width, -Width, Rise time, Fall time, +Duty cycle, -Duty cycle, +Overshoot, High, Low, Max, Min, Peak-to-peak, Amplitude, Mean, Cycle mean, RMS, Cycle RMS, Burst width, Delay, Phase, Area¹, Cycle Area¹
Measurement Statistics	Mean, Min, Max, Standard deviation. Requires TDS3AAM application module
Thresholds	User-definable thresholds for automatic measurements; settable in percent or voltage
Gating	Isolate a specific occurrence within an acquisition to take measurements, using either the screen or cursors

*¹ Requires TDS3AAM application module.

Waveform Math

Characteristic

Description

Arithmetic

Add, subtract, multiply, and divide waveforms

Spectral magnitude. Set FFT vertical scale to Linear RMS or dBV RMS, and FFT window to Rectangular, Hamming, Hanning, or Blackman-Harris

Advanced Math*¹

Integrate, Differentiate, Define extensive algebraic expressions including analog waveforms, math functions, scalars, up to two user-adjustable variables and results of parametric measurements. For example: (Intg (Ch1-Mean(Ch1)) × 1.414 × VAR1)

Note: Requires TDS3AAM application module.

*¹ Requires TDS3AAM application module.

Waveform Processing

Characteristic	Description
Autoset	Single-button, automatic setup of all channels for vertical, horizontal and trigger systems, with undo autoset
Deskew	Channel-to-channel deskew ±10 ns may be manually entered for better timing measurements and more accurate math waveforms

Display Characteristics

Characteristic	Description
Display Type	6.5 in. (165.1 mm) liquid-crystal TFT color display
Display Resolution	640 horizontal × 480 vertical pixels (VGA)
Interpolation	Sin(x)/x
Waveform styles	Dots, vectors, variable persistence, infinite persistence
Graticules	Full, grid, crosshair, and frame. NTSC, PAL, SECAM, and vectorscope (100% and 75% color bars) with optional TDS3VID or TDS3SDI application modules
Format	YT, XY, and Gated XYZ (XY with Z-axis blanking available on 4-channel instruments only)

Power Source

Characteristic	Description
AC line power
Source voltage	100 V_RMS to 240 V_RMS ±10%
Source frequency	45 Hz to 440 Hz from 100 V to 120 V 45 Hz to 66 Hz from 120 V to 240 V
Power consumption	75 W maximum
Battery power	Requires TDS3BATC, rechargeable lithium ion battery pack
Operating time, typical	3 hours

Environmental and Safety

Characteristic	Operating	Non-operating
Temperature	0 ºC to +50 ºC	-40 ºC to +71 ºC
Humidity	Operating and Nonoperating: Up to 95% RH at or below +30 ºC Operating and Nonoperating: Up to 45% RH +30 ºC up to +50 ºC
Altitude	To 3,000 m	15,000 m
Electromagnetic Compatibility	Meets or exceeds EN61326 Class A, Annex D radiated and conducted emissions and immunity; EN6100-3-2 AC Powerline Harmonic Emissions; EN6100-3-3 Voltage Changes, Fluctuation, and Flicker; FCC 47 CFR, Part 15, Subpart B, Class A; Australian EMC framework
Safety	UL61010B-1, CSA1010.1, IEC61010-1, EN61010-1

Physical Characteristics

Instrument
Dimensions	mm	in.
Width	375.0	14.8
Height	176.0	6.9
Depth	149.0	5.9
Weight	kg	lb.
Instrument only	3.2	7.0
with accessories	4.5	9.8
Instrument Shipping
Package Dimensions	mm	in.
Width	502.0	19.8
Height	375.0	14.8
Depth	369.0	14.5
Rackmount (RM3000)
Dimension	mm	in.
Width	484.0	19.0
Height	178.0	7.0
Depth	152.0	6.0