For full functionality of this site it is necessary to enable JavaScript.

SONEL MMR-630 Microohmmeter (0.1μΩ ~1999,9 Ω, 10A)

-  Measurement of resistive object type:

+ welded and soldered connections, equipotential bonding, earth wire,

+ terminals and connectors, rail welded joints, cables and wires,

+ measurement 4-pole method.

 - Measurement of inductive object type:

+ coils (motors and transformers), low resistance coils.

- Range/ Resolution                           

+ 0...999,9μΩ /0,1μΩ (Current test 10 A)      

+ 1,0000...1,9999 mΩ /0,0001 mΩ (Current test 10 A)                              

+ 2,000...19,999 mΩ /0,001 mΩ (Current test 10 A)                                   

+ 20,00...199,99 mΩ /0,01 mΩ (Current test 1 A)       

+ 200,0...999,9 mΩ /0,1 mΩ (Current test 0,1 A)         

+ 1,0000...1,9999 Ω /0,0001 Ω (Current test 0,1 A       )              

+ 2,000...19,999 Ω /0,001 Ω (Current test 10 mA)      

+ 20,00...199,99 Ω /0,01 Ω (Current test 0,1 mA)        

+ 200,0...1999,9 Ω /0,1 Ω (Current test 0,1 mA)          

-Accuracy : ±(0,25% m.v. + 2 digits)

Includes:

- Test lead 3m (2 pcs.) WAPRZ003DZBB

- „Crocodile” clip K03; black (4 pcs.) WAKROBL30K03

- Kelvin vice K06 (2 psc.) WAKROKELK06

- Carrying case L1 WAFUTL1

- Cable for battery charger WAPRZLAD230

- Ni-MH battery package 4,8V 3Ah WAAKU03

- RS-232 serial transmission cable  WAPRZRS232

- Double pin Kelvin probe (2 pcs.) WASONKEL2OGB

- Hanging straps WAPOZSZE1

- User manual

- Calibration certificate issued by calibration laboratory (MMR-630) LSWPLMMR630

 

Details

Compare model: SKB MIKO-7, SKB MIKO-8, Metrel MI 3250, Sonel MMR 630, Vanguard WRM-10

Data Sheets

 

  • Measurement of resistive object type:
    - welded and soldered connections, equipotential bonding, earth wire,
    - terminals and connectors, rail welded joints, cables and wires,
    - measurement 4-pole method.
  • Measurement of inductive object type:
    - coils (motors and transformers), low resistance coils.
  • Range selection autoranging or manual (measurement of inductive object type).
  • Selectable measurement mode adjusted to object type:
    - for resistive objects - fast mode (3 seconds),
    - for inductive objects - long mode with automatic discharge after measurements (or with lower accuracy - shorter mode).
  • Selectable measurement mode adjusted to application:
    - normal mode - after pushing „START” button,
    - automatic mode - since test leads are connected to the object meters automatically starts measurement with dual direction current flow and gives average result - what eliminates eventual DC voltage on tested object,
    - continuous mode - every 3 seconds for resistive objects or continuous measurement for inductive objects.
  • Window mode:
    - this option enables setting an upper and a lower limit between which the average measurement result is bound to appear. The results outside of this range will be indicated by two long audible signals and the symbols.
  • MMR-630 is designated not to be effected by interference up to 20 mV and to show noises from 20 to 100 mV (so in edge conditions even 5 times higher than measured drop of potential).
  • Memory store for up to 990 results and a communications facility for transferring data from the device to a PC.

Electric security:
- type of insulation: double, according to EN 61010 - 1 and IEC 61557
- measurement category: CAT III 300 V acc. to EN 61010 - 1
- protection class acc. to EN 60529: IP54

Other technical data:
- meter’s power supply: battery package SONEL/Ni-MH 4,8 V
- battery charging time: approx. 2,5 hours
- number of measurements with the current of 10 A: 300
- auto-off time: 120 seconds
- immunity to interference: additional error ≤1% for voltage 50 Hz ≤100 mV RMS
- maximum leads resistance for the 10 A current: 0,1 Ω
- maximum inductance of the tested object: 40H
- accuracy of the test current: ±10%
- resistance measurement time:
- with the selected resistive object type with the bidirectional current: 3 seconds
- with the selected inductive object type, dependant on the resistance
and inductance of the object: a few minutes (max. 10)
- dimensions: 295 x 222 x 95 mm
- weight: approx. 1,7 kg

Rated operational conditions:
- operation temperature: 0...+40°C
- storage temperature: -20...+60°C

MMR-620 microohmmeter conforms the following directives
or standards according to CE requirements.

Directive:
Low Voltage Directive (LVD) 73/23/EEC, 93/68/EEC.

Standards: 
EN 61010 - 1:2001 Safety requirements for electrical equipment for measurement, control and laboratory use. General requirements .
EN 61010 - 031:2002: Safety requirements for electrical equipment for measurement, control and laboratory use. Safety requirements for hand-held probe assemblies for electrical measurement and test.

Directive: 
Electromagnetic compatibility (EMC) 89/336/EEC, 92/31/EEC, 93/68/EEC.

Standards:
EN 61326:1997+A1:1998+A2:2001 Electrical equipment for measurement, control and laboratory use - EMC requirements.

Resistance measurement

MMR-630CurrentAccuracy
RangeResolution
0...999,9μΩ0,1μΩ10 A±(0,25% m.v. + 2 digits)
1,0000...1,9999 mΩ0,0001 mΩ
2,000...19,999 mΩ0,001 mΩ
20,00...199,99 mΩ0,01 mΩ1 A
200,0...999,9 mΩ0,1 mΩ0,1 A
1,0000...1,9999 Ω0,0001 Ω
2,000...19,999 Ω0,001 Ω10 mA
20,00...199,99 Ω0,01 Ω0,1 mA
200,0...1999,9 Ω0,1 Ω0,1 mA

- input impedance of the voltmeter: ≥200 kΩ

„m.v.” - measured value.

 

  • 품질 보증
  • 공인 보증
  • 집으로 배달
  • 간단하게 거래하기

할인과 정보를 받기 위해 등록하기