EMIN completed training module "Proceq Metal Instrument Standardized Service" in Singapoore

12/05/y 09:37:28

Recently, EMIN has successfully completed the TRAINING MODULE "Proceq Metal Instrument Standardized Service" and is now authorized to carry out repairs, r

Recently, EMIN has successfully completed the TRAINING MODULE
"Proceq Metal Instrument Standardized Service"
and is now authorized to carry out repairs, replacements, upgrades and calibration of Proceq Concrete Instrument
Place: Proceq Asia Pte Ltd, Singapore
Date: 10th 11th May, 2018

The training modules covered the following specific topics:
• Functionality and operation of instrument
• Failure analysis of instrument and components
• Repairs of instrument and components
• Calibration of instrument and components
• Software Upgrade of instrument
The instruments covered were the Universal Platform, Equotip3 & Equotip Piccolo / Bambino.

ຂ່າວທີ່ກ່ຽວຂ້ອງ

10/08/y 17:23:32

Testing Crankshaft Position Sensors With an OWON Oscilloscope

A practical overview of using the OWON VDS2064 PC oscilloscope to examine magnetoelectric crankshaft position sensor waveforms, identify changing signal patterns, and compare correct and reversed terminal connections.

10/08/y 17:05:19

Testing Hall Camshaft Sensors with an OWON Oscilloscope

A practical overview of connecting an oscilloscope, observing Hall camshaft sensor waveforms, and comparing timing characteristics in automotive diagnostic work.

10/08/y 17:04:12

CAN Comfort Waveform Testing with OWON Oscilloscopes

A practical overview of observing CAN Comfort signals in Volkswagen PASSAT B7 maintenance, including sleep-state readings and relevant OWON TAO3000 series features.

10/08/y 15:42:43

Automotive Throttle Sensor Testing with OWON TAO3000

This practical overview explains how the OWON TAO3000 series and TAO3104A can be used to observe dual throttle position sensor signals during automotive testing.

10/08/y 14:16:08

Comparing Shore A and Shore D Hardness: Two Common Hardness Scales Today

Both Shore A and Shore D are used to measure material hardness, but each scale is suited to a different group of materials. Soft rubber, silicone, or elastic gaskets are typically tested using Shore A, whereas hard plastics, engineering plastics, and materials with low deformation are better suited to Shore D

ຕິດຕາມຂ່າວສານ ແລະ ຂໍ້ສະເໜີ

ຮັບສ່ວນຫຼຸດພິເສດຕາມປະລິມານ, ອັບເດດລາຄາຂາຍສົ່ງ ແລະ ການແຈ້ງເຕືອນສິນຄ້າໃໝ່ສົ່ງກົງເຖິງອິນບັອກຂອງທ່ານ.

ໂດຍການສະໝັກສະມາຊິກ, ທ່ານຍອມຮັບ ເງື່ອນໄຂການໃຫ້ບໍລິການ ແລະ ນະໂຍບາຍຄວາມເປັນສ່ວນຕົວ ຂອງພວກເຮົາ.

ການຊ່ວຍເຫຼືໍາດ່ວນ

ເຂົ້າເຖິງຜູ້ຊ່ຽວຊານທີ່ໄດ້ຮັບການຢັ້ງຢືນຂອງພວກເຮົາໂດຍກົງ