For full functionality of this site it is necessary to enable JavaScript.
EMIN.VN
0

HIOKI ROADSHOW DONG NAI 2025

28/04/y 10:38:58

Following the success of Roadshow HIOKI 2024, in response to customer expectations, on May 23, 2025, EMIN continues to cooperate with HIOKI to organize a special program "A Golden Day - Ten Thousand Words of Gratitude" for customers who love HIOKI products and have always trusted and used EMIN's services over the past time.

This will be an opportunity for customers to own high-quality electrical measuring, resistance measuring, insulation testing equipment... from the HIOKI brand at extremely attractive preferential prices and many valuable gifts.

Huge Offer - Limited Quantity

In this event, EMIN and HIOKI offer a 10% discount on 14 outstanding product models, each model is only applicable to the first 20 products. Applicable models include:

- CM3289, 3288-20

- CM4373-50, CM4375-50

- DT4261, DT4282

- FT6031-50, FT6041

- PD3129-10, 3481-20

- IR4053-10, P2010

- IR5051, Z3210

Not only good price, when buying the following models: 3244-60, 3280-10F, 3288, DT4256, IR4056-21, you will also receive the following gifts

- Multi charging cable HIOKI

- Genuine HIOK HelmetI

In particular, with every order from 9 million VND or more, you will immediately receive a HIOKI 3481-20 electric tester completely free of charge. A small but extremely useful gift for daily work, supporting quick and safe voltage testing.

Time and venue:

- Time: 9:30 – 16:00, May 23, 2025 

- Location: Front hall of EMIN Dong Nai office, 

No. 458 Dong Khoi, Tan Hiep Ward, Bien Hoa City, Dong Nai Province 

The number of products and gifts is limited, so don't hesitate! Come to "A Golden Day - Thousands of Gratitudes" with EMIN and HIOKI on May 23 to choose the right equipment for your work needs with this super attractive discount 

We are very pleased to welcome and serve you at EMIN Dong Nai!

ຂ່າວທີ່ກ່ຽວຂ້ອງ

Comparing Shore A and Shore D Hardness: Two Common Hardness Scales Today
10/08/y 14:16:08

Both Shore A and Shore D are used to measure material hardness, but each scale is suited to a different group of materials. Soft rubber, silicone, or elastic gaskets are typically tested using Shore A, whereas hard plastics, engineering plastics, and materials with low deformation are better suited to Shore D

What causes equipment to restart automatically in the factory, and how can the fault be identified?
10/08/y 11:17:47

Equipment restarts in a factory setting can be attributed to voltage sags, momentary power outages, electrical noise, overheating, or hardware faults. For incidents that last only a few power cycles, a power quality analyzer can capture voltage, current, and waveform data at the exact moment of the reset, thereby helping engineers determine whether the power supply is the cause

Why Measured Amplitude Can Be Lower Than the Real Value
10/08/y 09:27:59

An oscilloscope can display a lower amplitude than expected when its bandwidth is too limited for the signal being measured. This article explains the relationship between bandwidth, rise time, and measurement accuracy.

ຕິດຕາມຂ່າວສານ ແລະ ຂໍ້ສະເໜີ

ຮັບສ່ວນຫຼຸດພິເສດຕາມປະລິມານ, ອັບເດດລາຄາຂາຍສົ່ງ ແລະ ການແຈ້ງເຕືອນສິນຄ້າໃໝ່ສົ່ງກົງເຖິງອິນບັອກຂອງທ່ານ.

ໂດຍການສະໝັກສະມາຊິກ, ທ່ານຍອມຮັບ ເງື່ອນໄຂການໃຫ້ບໍລິການ ແລະ ນະໂຍບາຍຄວາມເປັນສ່ວນຕົວ ຂອງພວກເຮົາ.

ການຊ່ວຍເຫຼືໍາດ່ວນ

ເຂົ້າເຖິງຜູ້ຊ່ຽວຊານທີ່ໄດ້ຮັບການຢັ້ງຢືນຂອງພວກເຮົາໂດຍກົງ