For full functionality of this site it is necessary to enable JavaScript.
EMIN.VN
0

Hội thảo Diễn đàn đo lường Keysight (KMF) 2024

21/11/y 13:53:18

Ngày 15/11/2024 vừa qua, EMIN GROUP và 3 đơn vị MITAS, ASIC, NDV phối hợp cùng Keysight tổ chức hội thảo Diễn đàn đo lường Keysight (KMF) tại khách sạn JW Marriott Hà Nội

Keysight Measurement Forum (KMF) is an important event of Keysight Technologies held across Southeast Asia to share technology trends and innovations in the industry. This forum brings new knowledge about 6G technology, advanced circuit design, and high-speed digital. This is a place that connects businesses and experts in the electronics and semiconductor value chain, striving to find solutions for field inspection areas.

Since November 2014, Keysight Technologies is a subsidiary separated from Agilent Technologies, officially operating with full functions and authority to operate the electronic measurement equipment segment of the former Agilent. From here, all product names, documents, and certifications bearing the Agilent brand name were renamed Keysight.

And since November 2020, EMIN has officially become a direct distributor of Keysight in Vietnam.

At the conference, leading experts from Keysight shared about breakthroughs in the fields of 5G, 6G, Semiconductor Circuit Design and High-Speed ​​Digital Technology. In addition, attendees will also have a hands-on experience with many of Keysight's most advanced equipment in the showroom area, including the exhibition booths of EMIN Group and other partners.

During the organization, the EMIN GROUP team and Keysight's senior experts are pleased to bring you the latest updated knowledge in the field of measurement and testing such as 6G and 5G connection technology. NTN, High Speed ​​Digital and Semiconductor Circuit Design.

Once again, EMIN GROUP would like to sincerely thank you for your interest in attending the event.

Below are the images we captured at the conference:

ຂ່າວທີ່ກ່ຽວຂ້ອງ

Comparing Shore A and Shore D Hardness: Two Common Hardness Scales Today
10/08/y 14:16:08

Both Shore A and Shore D are used to measure material hardness, but each scale is suited to a different group of materials. Soft rubber, silicone, or elastic gaskets are typically tested using Shore A, whereas hard plastics, engineering plastics, and materials with low deformation are better suited to Shore D

What causes equipment to restart automatically in the factory, and how can the fault be identified?
10/08/y 11:17:47

Equipment restarts in a factory setting can be attributed to voltage sags, momentary power outages, electrical noise, overheating, or hardware faults. For incidents that last only a few power cycles, a power quality analyzer can capture voltage, current, and waveform data at the exact moment of the reset, thereby helping engineers determine whether the power supply is the cause

Why Measured Amplitude Can Be Lower Than the Real Value
10/08/y 09:27:59

An oscilloscope can display a lower amplitude than expected when its bandwidth is too limited for the signal being measured. This article explains the relationship between bandwidth, rise time, and measurement accuracy.

ຕິດຕາມຂ່າວສານ ແລະ ຂໍ້ສະເໜີ

ຮັບສ່ວນຫຼຸດພິເສດຕາມປະລິມານ, ອັບເດດລາຄາຂາຍສົ່ງ ແລະ ການແຈ້ງເຕືອນສິນຄ້າໃໝ່ສົ່ງກົງເຖິງອິນບັອກຂອງທ່ານ.

ໂດຍການສະໝັກສະມາຊິກ, ທ່ານຍອມຮັບ ເງື່ອນໄຂການໃຫ້ບໍລິການ ແລະ ນະໂຍບາຍຄວາມເປັນສ່ວນຕົວ ຂອງພວກເຮົາ.

ການຊ່ວຍເຫຼືໍາດ່ວນ

ເຂົ້າເຖິງຜູ້ຊ່ຽວຊານທີ່ໄດ້ຮັບການຢັ້ງຢືນຂອງພວກເຮົາໂດຍກົງ