Máy phân tích chất lượng tín hiệu Anritsu MP1800A | EMIN.VN

Máy phân tích chất lượng tín hiệu Anritsu MP1800A

Name: Máy phân tích chất lượng tín hiệu Anritsu MP1800A
Brand: ANRITSU

Có sẵn: 0 Cái

Hãng sản xuấtANRITSU

ModelMP1800A

Liên hệ

Số lượng

Thanh toán an toàn

Hỗ trợ chuyên nghiệp

Đổi trả dễ dàng

Giao hàng tận nơi

Brochure

Signal Quality Analyzer MP1800A Series
MP1800A Series 32 Gbit/s Signal Integrity Test Solution (32G Multi-CH PPG/ED)
4 Tap Emphasis MP1825B
56G/64G bit/s Test Solution (56G/64G MUX/DEMUX)

Operations Manual

MU181020A 12.5 Gbit/s PPG MU181020B 14 Gbit/s PPG Operation Manual
MU181040A 12.5 Gbit/s ED MU181040B 14 Gbit/s ED Operation Manual
MU182020A 25Gbit/s 1ch MUX MU182021A 25Gbit/s 2ch MUX Operation Manual
MU182040A 25Gbit/s 1ch DEMUX MU182041A 25Gbit/s 2ch DEMUX Operation Manual
MX181500A Jitter/Noise Tolerance Test Software Operation Manual
MU181500B Jitter Modulation Source Operation Manual
MP1800A Signal Quality Analyzer Operation Manual
MT1810A 4 Slot Chassis Operation Manual
MP1800A Signal Quality Analyzer Installation Guide
MT1810A 4 Slot Chassis Installation Guide
MX180000A Signal Quality Analyzer Control Software Operation Manual
MU181000A 12.5 GHz Synthesizer MU181000B 12.5 GHz 4 port Synthesizer Operation Manual
MU181800A 12.5 GHz Clock Distributor MU181800B 14 GHz Clock Distributor Operation Manual
MP1821A 50G/56Gbit/s MUX Operation Manual
MX180000A Signal Quality Analyzer Control Software Operation Manual Remote Control

Features

Highly expandable, plug-in, modular design bit error rate tester (BERT)
Bit Error Rate test from 0.1 Gbit/s to 32.1 Gbit/s; 56 Gbit/s with external MUX/DeMUX
Supports signal integrity analysis for a variety of 100G+ applications
- High speed backplane and interconnect
- High speed chip/device
- Active optical cable
- Optical transceiver modules
High-quality (12 ps rise/fall time) and low-jitter (8 ps p-p) PPG waveform, up to 3.5 Vp-p
Jitter tolerance test up to 32.1 Gbit/s
- SJ up to 2000 UI. High modulation frequency SJ up to 1 UI at 250 MHz
- Support generation of dual tone SJ, RJ, BUJ, and SSC
- Half Period Jitter (Even/Odd Jitter)
Ultra high sensitivity Error Detector (10 mV typical) with embedded clock recovery
32.1 Gbit/s 4Tap Emphasis with external MP1825B
Crosstalk test and skew tolerance test using synchronized multi-channel PPG
Passive Linear Equalizers for improved EYE opening
Comprehensive signal analysis including Burst measurement for PON and EDFA loop circuit testing, Bathtub Measurement (TJ, DJ, RJ), Eye Diagram and Eye Margin Measurement
32.1 Gbaud 4PAM/8PAM generators and accurate 4PAM BER measurement
1 Tbit/s Next Gen. High-Speed Transmission Testing (32G x 32ch)

New Product Information：

MP1861A 56G/64G bit/s MUX NEW
MP1862A 56G/64G bit/s DEMUX NEW

Desription

High Quality Instrument Provides Highly Accurate Results

Anritsu Signal Quality Analyzer (MP1800A) incorporates a Pulse Pattern Generator (PPG) module for generating the highest-quality, highest-amplitude signals in the industry, as well as an Error Detector (ED) module with the highest input sensitivity available.

The number of channels per MP1800A-series PPG or ED module can be selected from 1ch, 2ch or 4ch, supporting multichannel synchronization for up to 8 channels at 32 Gbit/s. As a result, each channel of AOC, CFP, CXP, QSFP+, etc., modules can be measured simultaneously, enabling crosstalk and skew tolerance evaluation tests.

The MP1800A PPG modules offer outputs up to 3.5 Vp-p, supporting the evaluation of modulators, such as EA and EML. In addition to generating IEEE and ITU-T burst and auxiliary signals for evaluating E-PON, G-PON, and 10GE-PON optical modules, the product automated generation of burst data and auxiliary signal output timings shortens evaluation times and improves evaluation quality.

Complete 32G Jitter Testing with Clock Recovery in One Box

Anritsu MP1800A with Low-Intrinsic Jitter PPG, 4TAP Emphasis, High-Sensitivity ED, Equalizer for Eye Opening compensation, and automatic measurement software is the ideal total solution for Jitter Tolerance tests.

Various types of jitter, such as SJ, RJ, BUJ, SSC can be generated using the built-in jitter modulation source. The Jitter Modulator generates wide-amplitude SJ up to 1 UI at a Jitter Frequency of 250 MHz, ensuring sufficient margin for receiver Jitter Tolerance tests. Additionally, the Intrinsic Jitter of 275 fs rms (nominal) is extremely low, not only when Jitter modulation is OFF but also when 0 UI is set at Jitter ON, ensuring accurate measurements even at low Jitter amplitudes.

Combining the MP1800A with the 4Tap Emphasis (MP1825B) supports the generation of pre-emphasis for high-speed interconnect standards up to 32.1 Gbit/s, such as CEI-28G, 32G Fibre Channel, and InfiniBand EDR (26G). Each tap can be changed independently assuring accurate pre-emphasis. Positioning the instrument as an external remote head, as close as possible to the DUT, minimizes the impact of signal degradation due to cable-loss and ISI, thus maintaining the highest signal quality at the DUT interface.

The ED module has a high sensitivity of just 10 mV as well as high-speed auto-adjustment of 1 second or less (auto-detects threshold level and phase point), supporting accurate and efficient measurement of low-output-amplitude devices, such as AOCs. Installing the Clock Recovery option enables stress jitter tolerance tests of SERDES with different Tx and Rx clocks and BER measurements of clock-less devices such as AOC in one box.

When used in combination with the High Sensitivity ED (MU183040B/41B) the Passive Linear Equalizers (J1621A/J1622A) enable BER and Jitter Tolerance testing of PHY devices with low EYE openings. The equalizers compensate for printed circuit board (PCB) trace loss and improve EYE opening, thus minimizing the impact of high frequency transmission line distortion.

Ultra High-Speed Signal Generation and BER Measurement

The MP1800A can be configured to generate the high quality, low S/N, 4PAM and 8PAM data signals required for the characterization of high-speed backplanes and 400 GbE interfaces using the 4PAM/8PAM Converter (MZ1834A/MZ1838A). The bit error rates of three 4 PAM eye patterns can be measured simultaneously. The MP1800A is the ideal platform for accurate BER measurements of 4 PAM signals using the long-memory programmable pattern function and error-mask function for filtering out unwanted errors.

With the ability to synchronize up to four MP1800A Signal Quality Analyzer units, only Anritsu supports the configuration of an ultra-high-speed transmission test system up to 1 Tbit/s with multi-channel synchronization signals, such as Quad DP-16QAM and Dual DP-64QAM.

Applications

The MP1800A Series provides solutions for:

Ultra High Speed Backplane Test Solution - crosstalk, emphasis and skew tolerance test
40 Gbit/s Optical Modulation Test Solution - I/Q signal transmission test
100G ethernet Device Test Solution - high quality and functional test signals
Manufacturing Solution for Multiple Optical Modules and High-Speed Connectors - low cost and low power consumption
Evaluation of PON devices for the burst data

Available application software for:

Eye Margin. Q Measurement, Bit Error Analysis using ISI, Eye Diagram, and Bathtub (standard embedded applications)
Jitter generation and jitter tolerance test
SONET/SDH/1G ethernet/10G ethernet Pattern Editor
PON

Signal Quality Analyzer MP1800A

Number of slots	6 slots
LCD Display	8.4-inch Color TFT, 800×600 pixels
Peripheral Interface	VGA out (SVGA), USB 1.1 (3 ports)
Remote Interface	GPIB [MP1800A-001], LAN (2 ports) [MP1800A-002]
Dimensions and Mass	320 (W) × 177 (H) × 450 (D) mm, ≤13 kg (without modules)

■ 4Slot Chassis MT1810A

Number of slots	4 slots
LCD Display	No
Remote Interface	LAN (2 ports)
Dimensions and Mass	350 (W) × 132.5 (H) × 400 (D) mm, ≤13 kg (without modules)

■ 28G/32G bit/s PPG MU183020A

Model No.	No Option	MU183020A-001
Operation Bit-rate	2.4 Gbit/s to 28.1 Gbit/s	2.4 Gbit/s to 32.1 Gbit/s

Model No.	MU183020A-012	MU183020A-013	MU183020A-022	MU183020A-023
Number of Outputs	2 (Data, xData)	2 (Data, xData)	4 (Data1, xData1, Data2, xData2)	4 (Data1, xData1, Data2, xData2)
Amplitude/Output Level	0.5 Vp-p to 2.0 Vp-p	0.5 Vp-p to 3.5 Vp-p	0.5 Vp-p to 2.0 Vp-p	0.5 Vp-p to 3.5 Vp-p

■ 28G/32G bit/s 4ch PPG MU183021A

Model No.	No Option	MU183021A-001
Operation Bit-rate	2.4 Gbit/s to 28.1 Gbit/s	2.4 Gbit/s to 32.1 Gbit/s

Model No.	MU183021A-012	MU183021A-013
Number of Outputs	8 (Data1, xData1, Data2, xData2, Data3, xData3, Data4, xData4)	8 (Data1, xData1, Data2, xData2, Data3, xData3, Data4, xData4)
Amplitude/Output Level	0.5 Vp-p to 2.0 Vp-p	0.5 Vp-p to 3.5 Vp-p

■ 28G/32G bit/s High Sensitivity ED MU183040B

Model No.	No Option	MU183040B-001
Operation Bit-rate	2.4 Gbit/s to 28.1 Gbit/s	2.4 Gbit/s to 32.1 Gbit/s

Model No.		MU183040B-010	MU183040B-020
Number of Inputs		2 (Data, xData)	4 (Data1, xData1, Data2, xData2)
Input Sensitivity	EyE Amplitude	15 mVp-p (typ.), ≤25 mVp-p 28.1 Gbit/s, Single-end, PRBS2³¹-1	15 mVp-p (typ.), ≤25 mVp-p 28.1 Gbit/s, Single-end, PRBS2³¹-1
Input Sensitivity	EyE Height	10 mVp-p (typ.) 28.1 Gbit/s, Single-end, PRBS2³¹-1	10 mVp-p (typ.) 28.1 Gbit/s, Single-end, PRBS2³¹-1

Model No.	MU183040B-022	MU183040B-023
Operating Bit-rate	2.4 Gbit/s to 28.1 Gbit/s	25.5 Gbit/s to 32.1 Gbit/s
Loop bandwidth	<span style="font-size:12.0pt;font-family:"Times New Roman","serif"; mso-fareast-font-family:"Times New Roman