Máy kiểm tra lão hóa đèn Xenon Bevs BEVS 3360 (3000-4000 giờ, 340nm hoặc 300-400nm hoặc 420nm)

Đèn: Đèn xenon 6500W làm mát bằng nước

Tuổi thọ của đèn: 3000-4000 giờ

Bước sóng: 340nm hoặc 300-400nm hoặc 420nm

Bộ lọc quang học: Sự kết hợp khác nhau của các bộ lọc bên trong và bên ngoài như ánh sáng ban ngày, kính cửa sổ và bộ lọc UV mở rộng có sẵn

Phạm vi nhiệt độ buồng: + 35 °C -85 °C

Phạm vi nhiệt độ BPT: + 40 °C -110 °C

Phạm vi nhiệt độ BST: + 40 °C -120 °C

RH trong chu kỳ ánh sáng: 10% -75%

RH trong chu kỳ tối: 10-100%

Bức xạ:

340nm: 0.3-1.3W/m2

420nm: 0.55-2.75W/m2

300-400nm: 25-150W/m2

Dung tích mẫu: 67 giá đỡ mẫu kích thước 70×145mm

Kích thước: 1100×2050×1350mm (Rộng × Cao × Sâu)

Introduction

BEVS 3360 Intelligent Xenon Aging Tester is a high-performance testing device that uses a 6500W water-cooled xenon arc lamp as its light source, designed to simulate the full spectrum of natural sunlight, including ultraviolet, visible, and infrared light. This advanced equipment allows precise control over multiple environmental parameters, such as irradiance, temperature, relative humidity, and spray cycles, to replicate real-world outdoor conditions like sunlight, heat, moisture, and rain. The tester is widely used for accelerated aging tests on a variety of materials, such as coatings, plastics, textiles, automotive components, and construction materials.

Main Function

Irradiation Function

During the irradiation function, a water-cooled xenon lamp is utilized to simulate the damage effects of sunlight and the lamp control system regulates irradiance to ensure it meets the requirements stipulated in standards. The water cooling system removes the heat generated by the xenon lamp through circulating cooling water, maintaining it at an optimal operating temperature, thereby extending the service life of the xenon lamp.

Water Spray Function

Pure water from the external water purifier is pumped to the nozzles and then water droplets spray out uniformly to simulate rain and dew. The outer spray nozzle is pointed straight at the back of the aluminum panel, while the inner spray nozzle is pointed at the front of the panel.

Moisture Control Function

The humidifier automatically starts or stops the humidification function according to the set target humidity value. The circulating blower reduces the humidity inside the chamber by replenishing the air or increasing the circulating air volume. The humidity inside the chamber is controlled by the humidifier and the circulating blower.

Temperature Control Function

The circulating blower blows hot air into the interior of the chamber and uses the ventilation system to circulate the hot air inside the box so that the temperature inside the chamber rises evenly. Damper and VFD help decrease the temperature inside the chamber by replenishing air. A black panel thermometer or black standard thermometer is used to monitor the specimen surface temperature, which can be adjusted by the blower.

Features

Remote control and data transfer

Water spray onto the front and back side of specimens

Nine specimen areas can be controlled and sprayed independently

Automatic control and real-time display of temperature and humidity

Automatic calibration function with an alert system to remind users every 400 hours

A dedicated xenon lamp triggering system to enhance lamp lifespan (the xenon lamp can be triggered 3–5 times in a short period)

Safe operation-Xenon lamp cooling water low-level protection, over-temperature protection, conductivity protection, over-temperature and low-temperature protection of the test rack and the test chamber, leakage, overcurrent and overload protection

Datasheet