For full functionality of this site it is necessary to enable JavaScript.
EMIN.VN
0

Hioki Year-End Promotion “Golden Offer – Power System Optimization”

26/09/y 09:38:31

Enjoy Hioki’s year-end Golden Offer to upgrade your power system. Promotion valid from September 1 to November 30, 2025, or while gifts last.

GOLDEN PROMOTION – IMPROVING ELECTRICAL SYSTEM

Power up, boost performance with HIOKI Gift Set

Applicable time: 01/09 – 30/11/2025, or while supplies last, whichever comes first

1. Time: Offer applies to orders placed from September 1, 2025 through November 30, 2025, or until gifts are sold out, whichever comes first.

2. Program details:

Customers receive 50% off the Wireless Adapter Z3210 when purchasing it with a Hioki Bluetooth-enabled field measuring device. Applicable devices: AC/DC Clamp Meter CM4371-50/ CM4373-50/CM4375-50AC Clamp Meter CM4141-50, Power Clamp Meter CM3286-50, Leakage Clamp Meter CM4001/ CM4002/ CM4003, Digital Multimeter DT4261Earth Tester FT6031-50/ FT6380-50, Insulation Resistance Tester IR4057-50Digital Phase Detector PD3259-50

Customers receive 30% off the P2010 high pressure probe when purchased with a compatible Hioki measuring device, including: AC/DC Clamp Meter CM4371-50/ CM4373-50/CM4375-50, AC Clamp Meter CM4141-50, Digital Multimeter DT4261

Free combo of DT4253 multimeter and 3481-20 electric tester for orders of PQ3100 power quality analyzer product

Free combo of DT4282 multimeter and 3481-20 electric tester for orders of PQ3198 power quality analysis product

Free combo of AC current clamp meter CM3289 and electric tester 3481-20 for orders of power recording products PW3360-20/ PW3360-21/ PW3365-20

3. Limits:

This offer cannot be used in conjunction with other promotions. 

4. General terms:

Hioki reserves the right to request additional information or documentation necessary to verify the validity of the order

The final decision on matters related to the promotion program belongs to Hioki

ຂ່າວທີ່ກ່ຽວຂ້ອງ

Comparing Shore A and Shore D Hardness: Two Common Hardness Scales Today
10/08/y 14:16:08

Both Shore A and Shore D are used to measure material hardness, but each scale is suited to a different group of materials. Soft rubber, silicone, or elastic gaskets are typically tested using Shore A, whereas hard plastics, engineering plastics, and materials with low deformation are better suited to Shore D

What causes equipment to restart automatically in the factory, and how can the fault be identified?
10/08/y 11:17:47

Equipment restarts in a factory setting can be attributed to voltage sags, momentary power outages, electrical noise, overheating, or hardware faults. For incidents that last only a few power cycles, a power quality analyzer can capture voltage, current, and waveform data at the exact moment of the reset, thereby helping engineers determine whether the power supply is the cause

Why Measured Amplitude Can Be Lower Than the Real Value
10/08/y 09:27:59

An oscilloscope can display a lower amplitude than expected when its bandwidth is too limited for the signal being measured. This article explains the relationship between bandwidth, rise time, and measurement accuracy.

ຕິດຕາມຂ່າວສານ ແລະ ຂໍ້ສະເໜີ

ຮັບສ່ວນຫຼຸດພິເສດຕາມປະລິມານ, ອັບເດດລາຄາຂາຍສົ່ງ ແລະ ການແຈ້ງເຕືອນສິນຄ້າໃໝ່ສົ່ງກົງເຖິງອິນບັອກຂອງທ່ານ.

ໂດຍການສະໝັກສະມາຊິກ, ທ່ານຍອມຮັບ ເງື່ອນໄຂການໃຫ້ບໍລິການ ແລະ ນະໂຍບາຍຄວາມເປັນສ່ວນຕົວ ຂອງພວກເຮົາ.

ການຊ່ວຍເຫຼືໍາດ່ວນ

ເຂົ້າເຖິງຜູ້ຊ່ຽວຊານທີ່ໄດ້ຮັບການຢັ້ງຢືນຂອງພວກເຮົາໂດຍກົງ