Máy hiệu chuẩn đa năng Powertek MC142
Hãng sản xuất: POWERTEK Model: MC142 - Yêu cầu báo giá
- Liên hệ
Tham khảo dịch vụ Hiệu chuẩn-Kiểm định và Sửa chữa
Gọi để có giá tốt
TP. Hà Nội: (024) 35.381.269
TP. Đà Nẵng: (023) 63.747.711
TP. Bắc Ninh: (0222) 730.39.68
TP. Hải Phòng: (0225) 730.03.89
TP. HCM: (028) 38.119.636
Đồng Nai: 0345.689.536
Hãng sản xuất: Powertek
Model: MC142
Xuất xứ: EU (anh)
Máy được dùng để hiệu chuẩn: Điện áp, dòng điện, công suất, điện trở, tụ điện, tần số.
- Điện áp ra AC/DC
+ Dải điện áp ra: 0mV~1000V
+ Dải tần: 20Hz đến 100kHz
+ Độ phân dải: 6½ dig.
+ Độ chính xác: 0.0010~ 0.005% tùy dải
- Dòng điện ra AC/DC
+ Dải tần: 20Hz đến 10kHz
+ Độ phân dải: 6½ dig.
+ Dải dòng điện ra: 1µA~ 30A (có thể mở rộng đến 1000A chọn mua thêm model 140-50)
+ Độ chính xác: 0.01%~~0.05% tùy dải
- Chức năng tín hiệu ra (tín hiệu không có hài)
+ Tín hiệu ra: 1mV đến 200V
+ Dòng điện ra: 100uA đến 2A
+ Dạng sóng: square positive, negative, symmetrical, saw A, B, triangle limited sin
Độ chính xác đỉnh: 0.3% + 50uV
Giá trị hiển thị: peak, calculated rms
Dải tần: tới 1000Hz cho điện áp, tới 120Hz cho dòng điện
- Điện trở và tụ điện:
+ Dải điện trở: 0 đến 1000 MΩ
+ Giải tụ: 900pF đến 100µF
+ Độ phân giải: 4 dig.
- Chức năng tần số:
+ Tổng dải tần: 0.1Hz đến 20MHz
+ Độ phân dải: 6 dig.
+ Độ chính xác: 0.005 %
+ Chế độ chức năng tần số:
PWM, fmax = 100kHz, Sóng vuông với hiệu chuẩn tỷ lệ và biên độ
HF, fmax = 20MHz, Sóng vuông với hiệu chuẩn tỷ lệ và biên độ
+ Chế độ PWM (0.1 Hz to 100 kHz)
+ Dải điện áp: 1mV~ 10V
+ Độ chính xác 0,1~0.2% tùy dải
- Mô phỏng cảm biến nhiệt độ RTD: Pt 100, Pt 200, Pt 1000, Ni 100
- Mô phỏng cảm biến TC: J, S, B, T, E, K, N
- Tích hợp đồng hồ vạn năng:
+V DC: 0 - 12V / 0.01 + 300uV/100uV
+ mA DC:0 - 25mA/ 0.015 + 150nA /100nA
+ mv DC: 0 - 2V/ 0.02 + 7uV/ 0.1 - 10uV
+ R: 0 - 2.5kOhm /0.02 + 10mOhm / 1 - 10mOhm
+ F: 1Hz - 15kHz /0.005 / 10uHz - 100mHz
+ Nhiệt độ TC: -250 - 1820oC /0.4 - 2.5oC/0.01oC
+ Nhiệt độ Pt: -200 - 850oC/ 0.1oC
Kích thước: 450 x 480 x 150 mm
Trọng lượng: 23kg
Nguồn: 115/230 V
Cung cấp kèm theo: CD HDSD, cáp nguồn, dây đo banana-banana 1000V-20A 2 cái, adapters cáp, Cáp RS232
(Đã ngưng sản xuất)
Chọn mua thêm phụ kiện:
Option 140-50 |
Cuộn dòng 25/50 vòng, dùng hiện chuẩn ampe kìm đến 1000A |
Cần thiết khi cần hiệu chuẩn ampe kìm |
||
Option 140-01 |
Bộ adapter dùng để hiệu chuẩn các loại đồng hồ vạn năng |
Cần thiết khi cần hiệu chuẩn đồng hồ vạn năng |
||
Option 10 |
Dây đo 20A/1000V (màu đen), Dài 1m |
Đã bao gồm 1 dây tiêu chuẩn theo máy, mua thêm để dự phòng |
||
Option 11 |
Dây đo 20A/1000V (màu đỏ), Dài 1m |
Đã bao gồm 1 dây tiêu chuẩn theo máy, mua thêm để dự phòng |
||
Option 20 |
Dây cáp BNC – BNC, Dài 1m |
Cần thiết để hiệu chuẩn các thiết bị tần số có cổng vào ra BNC |
||
Option 30 |
Dây cáp BNC – banana, Dài 1m |
Cần thiết để hiệu chuẩn các thiết bị tần số có cổng vào ra Banana |
||
Option 40 |
adapter Cáp Canon 25 / 2 x bananan, 1m, DC/mADC, (dùng để đo đòng điện và điện áp DC khi sử dụng tính năng đồng hồ vạn năng tích hợp trong máy) |
Cần thiết khi sử dụng tính năng đồng hồ vạn năng tích hợp trong máy |
||
Option 60 |
adapter Cáp Canon 25 / 4 x banana, 1 m (Dùng để đo điện trở 4W và nhiệt độ RTD khi sử dụng tính năng đồng hồ vạn năng tích hợp trong máy) |
Cần thiết khi sử dụng tính năng đồng hồ vạn năng tích hợp trong máy |
||
Option 70 |
Adapter Cáp dùng để mô phỏng điện trở 4W |
Cần thiết khi mô phỏng điện trở ra |
||
Option 80 |
Adapter cáp Canon 25 / 2 x banana (Dùng để đo mV DC và TC, (khi sử dụng tính năng đồng hồ vạn năng tích hợp trong máy) |
Cần thiết khi sử dụng tính năng đồng hồ vạn năng tích hợp trong máy |
||
Option 90 |
Cảm biến đo nhiệt độ PT100 ngoài (khi sử dụng tính năng đồng hồ vạn năng tích hợp trong máy) |
Cần thiết khi sử dụng tính năng đồng hồ vạn năng tích hợp trong máy |
||
|
2 cái adapter đầu ra ¾ inh |
Mua dự phòng |
||
Cable GPIB |
Cáp GPIB, 2m |
Chọn thêm nếu cần giao tiếp ghép nối máy tính qua công GPIB |
||
Cable RS-232 |
Cáp RS-232, 2m |
Đã có theo máy |
||
RS232 to USB CONVERTER |
Cáp chuyển đổi : RS232 sang USB |
Chọn thêm nếu cần chuyển đổi cổng RS232 sang USB nếu ghép nối máy tính |
Multifunction calibrator MC142 is a precision voltage, current and power calibration source serving as a measurement standard in calibration laboratories and production lines; where verification of electrical measurement equipment & sensors is required. It can be used for calibration and adjustment of meters measuring voltage, current, power, resistance, capacitance and frequency. Internal harmonic and non-harmonic signals make it possible to test electrical performance of meters using signals with various crest factors. Frequency modes enable selection of frequency, amplitude and duty cycle of the output signal. These are suitable for basic calibration of digital and analog oscilloscopes along with transient recorders. The calibrator is equipped to measure temperature with TC and RTD temperature sensors. Its built-in multimeter can be used independently or simultaneously with the calibrator output. Testing of transducers of various types, regulators and sensors can be performed, without the necessity to use any other measuring instrument. |
|
MC142 multifunction calibrator is available |
||||||||||||||||||||||||||||||||||||
Basic parameters |
||||||||||||||||||||||||||||||||||||||
Basic function of the calibrator is the generation of calibrated DC/AC voltage in the range from 0µV to 1000V and DC/AC current in the range from 0 to 30A. Using a 50-turn coil the current range can be extended to 1500A. The best accuracy of the calibrator on DC voltage ranges is 15ppm, on AC voltage ranges 250ppm, on DC current ranges 130ppm and on AC current ranges 550ppm. Maximum frequency range is from 20Hz to 100kHz for harmonic output waveform. The calibrator is equipped with a function generator for periodic non-harmonic signals with defined crest factor, making it possible to test sensitivity of multimeters to distorted signals. In addition the calibrator simulates resistance and capacitance, the resistance range from 0.0 Ohm to 1000MOhm and capacitance from 1nF to 100µF can be simulated exceeding the required precision for calibration of common hand-held multimeters. Basic accuracies are resistance ranges 150ppm and capacitance ranges 0.1%. Frequency function of the calibrator makes it possible to generate a square wave signal with adjustable and calibrated duty ratio, frequency and amplitude in range from 1mV to 10V in the frequency band up to 10kHz. In the mode HF the square wave signal up to 20MHz with a very low rise-time can be generated. The frequency functions are suitable for the calibrations of corresponding frequency ranges of the multimeters and for calibration of the channel sensitivities and time bases of the oscilloscopes as well. For calibrations of DC and one-phase AC power-meters and energy meters, the power – energy mode is determined. Output voltage can be set up to 240V and output current up to 20A with the power factor in range from -1 to +1 in the frequency band from 40Hz to 400Hz. Current capability of the voltage output is 30mA. It allows calibration of analogue power-meters which have higher current draw. For calibrations of the thermometers and temperature regulators, the function of simulation of temperature sensors is determined. Calibrator is able to simulate all common used Pt and Ni resistance sensors and TC sensors of the R, S, B, J, T, E, K and N types as well. Compensation of the TC cold junction is made either by entering value from the keyboard, or automatically by measuring the ambient temperature with Pt-100 sensor. The precision of the simulated resistance and TC sensors depends on set value and type of the sensor. For resistance sensors uncertainty band is in the range from 0.04°C to 0.5°C, for TC sensors from 0.4°C to 4.0°C. |
||||||||||||||||||||||||||||||||||||||
Built-in multimeter |
||||||||||||||||||||||||||||||||||||||
The MC142 internal multimeter has a basic capability to measure DC current to 20mA, DC voltage to 10V, resistance to 2kOhm and frequency to 15kHz as standard. With accuracy of 100ppm it enables measurement of output signals of various types of transducers. With external TC or resistance temperature sensors, temperature can be scaled, as can external strain gauge sensors, for pressure, torsion, strength, etc. actual units can be measured and displayed. |
||||||||||||||||||||||||||||||||||||||
Calibrator – Tester |
||||||||||||||||||||||||||||||||||||||
Calibrator can be used in simultaneous mode, i.e. selected output signal is generated and the response of the device under test is measured at the same time by internal multimeter. Programmable capability of the calibrator enables setting of 10 steps defined by output signal function and output value on source side and awaiting response of DUT measured by internal multimeter including allowed limits of the DUT. The testing can run automatically. |
||||||||||||||||||||||||||||||||||||||
Ease of use |
||||||||||||||||||||||||||||||||||||||
MC142 Calibrator is equipped with a number of other functions which make its use easier. Among them belong possibility to set relative deviations from the actual value of the selected output signal, displaying of the output signal uncertainty, internal calibration procedure and others. Concept of the calibrator control and indication uses a large area luminescence display on which all necessary information is concentrated. The control is perform by selection from the menu. Moreover, frequently used functions have firmly assigned keys with direct control. Normally, the calibrator is equipped with the GPIB bus and with the RS-232 serial port making it possible to be controlled by personal computer. The calibrator can be included into POWERTEK WinQbase/CALIBER software calibration systems. MC142 calibrator is derived from previous successful model MC-140. Against MC-140 model the new MC142 offers extended ranges and higher accuracy. |
||||||||||||||||||||||||||||||||||||||
Specifications |
||||||||||||||||||||||||||||||||||||||
|
- Cam kết chất lượng
- Bảo hành chính hãng
- Giao hàng tận nơi
- Đơn giản hóa giao dịch