Đăng ký nhận chiết khấu độc quyền, cập nhật giá sỉ và tin sản phẩm mới nhất ngay tại hộp thư của bạn.
Bằng cách đăng ký, bạn đồng ý với Điều khoản dịch vụ và Chính sách bảo mật của chúng tôi.
Kết nối trực tiếp với đội ngũ chuyên gia của chúng tôi
Băng thông : 500Mhz
Số kênh : 4
Rise time : 0.7ns
Tốc độ lấy mẫu : 5Gs/s mỗi kênh
Giới hạn băng thông : 20 Mhz, 150Mhz
Kiểu đầu vào : AC, DC, GND
Trở kháng vào : 1 MΩ và 50 Ω
Độ nhạy điện áp : 1 mV/div ~ 10 V/div (1 MΩ), 1 mV/div ~ 1 V/div
(50 Ω)
Độ phân giải : 9 bit
Điện áp lớn nhất đầu vào : 150 VRMS (1 MΩ) và 5 VRMS (50Ω)
Độ chính xác DC khuếch đại : ±2%
Thời gian quét : 1ns ~ 10s
Độ chính xác thời gian : ±20 ppm
Chế độ kích : Auto (supports Roll Mode for 40 ms/div and slower), Normal, Single Sequence
Màn hình : 6.5 inch, TFT
Độ phân giải màn hình : 640x480 pixel
Cổng kết nối : RJ-45, USB2.0, GPIB (option TDS3GV), RS-232C, VGA (option TDS3GV)
Nguồn cung cấp : 100 VRMS to 240 VRMS ±10%
Phụ kiện kèm theo : Máy chính, Que đo x 4, HDSD, chứng nhận chuẩn hãng.
TDS3000C Series Electrical Characteristics
|
Characteristic |
TDS3012C |
TDS3014C |
TDS3032C |
TDS3034C |
TDS3052C |
TDS3054C |
|---|---|---|---|---|---|---|
|
Bandwidth |
100 MHz |
100 MHz |
300 MHz |
300 MHz |
500 MHz |
500 MHz |
|
Calculated Rise Time (typical) |
3.5 ns |
3.5 ns |
1.2 ns |
1.2 ns |
0.7 ns |
0.7 ns |
|
Input Channels |
2 |
4 |
2 |
4 |
2 |
4 |
|
External Trigger Input |
Included on all models |
|||||
|
Sample Rate on each channel |
1.25 GS/s |
1.25 GS/s |
2.5 GS/s |
2.5 GS/s |
5 GS/s |
5 GS/s |
|
Record Length |
10 kpoints |
|||||
|
Vertical Resolution |
9 bits |
|||||
|
Vertical Sensitivity, 1 MΩ |
1 mV/div to 10 V/div |
|||||
|
Vertical Sensitivity, 50 Ω |
1 mV/div to 1 V/div |
|||||
|
Input Coupling |
AC, DC, GND |
|||||
|
Input Impedance |
1 MΩ in parallel with 13 pF or 50 Ω |
|||||
|
DC Gain Accuracy |
±2% |
|||||
|
Maximum Input Voltage, 1 MΩ |
150 VRMS with peaks at ≤400 V |
|||||
|
Maximum Input Voltage, 50 Ω |
5 VRMS with peaks at ≤30 V |
|||||
|
Position Range |
±5 div |
|||||
|
Bandwidth Limit |
20 MHz |
20 MHz |
20 MHz, 150 MHz |
20 MHz, 150 MHz |
20 MHz, 150 MHz |
20 MHz, 150 MHz |
|
Time Base Range |
4 ns to 10 s |
4 ns to 10 s |
2 ns to 10 s |
2 ns to 10 s |
1 ns to 10 s |
1 ns to 10 s |
|
Time Base Accuracy |
±20 ppm over any 1 ms time interval |
|||||
|
Input/Output Interfaces |
||||||
|
Ethernet Port |
RJ-45 connector, supports 10Base-T LAN |
|||||
|
USB Port |
Front-panel USB 2.0 host port Supports USB flash drive |
|||||
|
GPIB Port |
Full talk/listen modes, setting and measurements (Optional with TDS3GV Communications Module) |
|||||
|
RS-232-C Port |
DB-9 male connector, full talk/listen modes; control of all modes, settings and measurements Baud rates up to 38,400 (Optional with TDS3GV Communications Module) |
|||||
|
VGA Video Port |
DB-15 female connector, monitor output for direct display on large VGA-equipped monitors (Optional with TDS3GV Communications Module) |
|||||
|
External Trigger Input |
BNC connector, input impedance >1 MΩ in parallel with 17 pF; max input voltage is 150 VRMS |
|||||
Acquisition Modes
|
Mode |
Description |
|---|---|
|
DPO |
Captures and displays complex waveforms, random events and subtle patterns in actual signal behavior. DPOs provide 3 dimensions of signal information in real time: Amplitude, time, and the distribution of amplitude over time |
|
Peak Detect |
High-frequency and random glitch capture. Captures glitches as narrow as 1 ns (typical) using acquisition hardware at all time base settings |
|
WaveAlert® |
Monitors the incoming signals on all channels and alerts the user to any waveform that deviates from the normal waveform being acquired |
|
Sample |
Sample data only |
|
Average |
Waveform averaged, selectable from 2 to 512 |
|
Envelope |
Min-max values acquired over one or more acquisitions |
|
Single Sequence |
Use the Single Sequence button to capture a single triggered acquisition sequence at a time |
Trigger System
|
Characteristic |
Description |
|---|---|
|
Main Trigger Modes |
Auto (supports Roll Mode for 40 ms/div and slower), Normal, Single Sequence |
|
B Trigger |
Trigger after time or events |
|
Trigger After Time Range |
13.2 ns to 50 s |
|
Trigger After Events Range |
1 to 9,999,999 events |
Trigger Types
|
Trigger |
Description |
|---|---|
|
Edge |
Conventional level-driven trigger. Positive or negative slope on any channel. Coupling selections: AC, DC, Noise Reject, HF Reject, LF Reject |
|
Video |
Trigger on all lines or individual lines, odd/even or all fields on NTSC, PAL, SECAM |
|
Extended Video |
Trigger on specific lines in broadcast and non-broadcast (custom) standards and on analog HDTV formats (1080i, 1080p, 720p, 480p). Requires TDS3VID or TDS3SDI application module |
|
Pulse Width (or Glitch) |
Trigger on a pulse width <, >, =, ≠ to a selectable time limit ranging from 39.6 ns to 50 s |
|
Runt |
Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again |
|
Slew Rate |
Trigger on pulse edge rates that are either faster or slower than a set rate. Edges can be rising, falling, or either |
|
Pattern |
Specifies AND, OR, NAND, NOR when true or false for a specific time |
|
State |
Any logic state. Triggerable on rising or falling edge of a clock. Logic triggers can be used on combinations of 2 inputs (not 4) |
|
Comm |
Provides isolated pulse triggering required to perform DS1/DS3 telecommunications mask testing per ANSI T1.102 standard. Requires TDS3TMT application module |
|
Alternate |
Sequentially uses each active channel as a trigger source |
Waveform Measurements
|
Characteristic |
Description |
|---|---|
|
Cursors |
Amplitude, Time |
|
Automatic Measurements |
Display any four measurements from any combination of waveforms. Or display all measurements with measurement snapshot feature. Measurements include Period, Frequency, +Width, -Width, Rise time, Fall time, +Duty cycle, -Duty cycle, +Overshoot, High, Low, Max, Min, Peak-to-peak, Amplitude, Mean, Cycle mean, RMS, Cycle RMS, Burst width, Delay, Phase, Area*1, Cycle Area*1 |
|
Measurement Statistics |
Mean, Min, Max, Standard deviation. Requires TDS3AAM application module |
|
Thresholds |
User-definable thresholds for automatic measurements; settable in percent or voltage |
|
Gating |
Isolate a specific occurrence within an acquisition to take measurements, using either the screen or cursors |
*1 Requires TDS3AAM application module.
Waveform Math
|
Characteristic |
Description |
|---|---|
|
Arithmetic |
Add, subtract, multiply, and divide waveforms |
|
FFT |
Spectral magnitude. Set FFT vertical scale to Linear RMS or dBV RMS, and FFT window to Rectangular, Hamming, Hanning, or Blackman-Harris |
|
Advanced Math*1 |
Integrate, Differentiate, Define extensive algebraic expressions including analog waveforms, math functions, scalars, up to two user-adjustable variables and results of parametric measurements. For example: (Intg (Ch1-Mean(Ch1)) × 1.414 × VAR1) Note: Requires TDS3AAM application module. |
*1 Requires TDS3AAM application module.
Waveform Processing
|
Characteristic |
Description |
|---|---|
|
Autoset |
Single-button, automatic setup of all channels for vertical, horizontal and trigger systems, with undo autoset |
|
Deskew |
Channel-to-channel deskew ±10 ns may be manually entered for better timing measurements and more accurate math waveforms |
Display Characteristics
|
Characteristic |
Description |
|---|---|
|
Display Type |
6.5 in. (165.1 mm) liquid-crystal TFT color display |
|
Display Resolution |
640 horizontal × 480 vertical pixels (VGA) |
|
Interpolation |
Sin(x)/x |
|
Waveform styles |
Dots, vectors, variable persistence, infinite persistence |
|
Graticules |
Full, grid, crosshair, and frame. NTSC, PAL, SECAM, and vectorscope (100% and 75% color bars) with optional TDS3VID or TDS3SDI application modules |
|
Format |
YT, XY, and Gated XYZ (XY with Z-axis blanking available on 4-channel instruments only) |
Power Source
|
Characteristic |
Description |
|---|---|
|
AC line power |
|
|
Source voltage |
100 VRMS to 240 VRMS ±10% |
|
Source frequency |
45 Hz to 440 Hz from 100 V to 120 V 45 Hz to 66 Hz from 120 V to 240 V |
|
Power consumption |
75 W maximum |
|
Battery power |
Requires TDS3BATC, rechargeable lithium ion battery pack |
|
Operating time, typical |
3 hours |
Environmental and Safety
|
Characteristic |
Operating |
Non-operating |
|---|---|---|
|
Temperature |
0 ºC to +50 ºC |
-40 ºC to +71 ºC |
|
Humidity |
Operating and Nonoperating: Up to 95% RH at or below +30 ºC Operating and Nonoperating: Up to 45% RH +30 ºC up to +50 ºC |
|
|
Altitude |
To 3,000 m |
15,000 m |
|
Electromagnetic Compatibility |
Meets or exceeds EN61326 Class A, Annex D radiated and conducted emissions and immunity; EN6100-3-2 AC Powerline Harmonic Emissions; EN6100-3-3 Voltage Changes, Fluctuation, and Flicker; FCC 47 CFR, Part 15, Subpart B, Class A; Australian EMC framework |
|
|
Safety |
UL61010B-1, CSA1010.1, IEC61010-1, EN61010-1 |
|
Physical Characteristics
|
Instrument |
||
|---|---|---|
|
Dimensions |
mm |
in. |
|
Width |
375.0 |
14.8 |
|
Height |
176.0 |
6.9 |
|
Depth |
149.0 |
5.9 |
|
Weight |
kg |
lb. |
|
Instrument only |
3.2 |
7.0 |
|
with accessories |
4.5 |
9.8 |
|
Instrument Shipping |
||
|
Package Dimensions |
mm |
in. |
|
Width |
502.0 |
19.8 |
|
Height |
375.0 |
14.8 |
|
Depth |
369.0 |
14.5 |
|
Rackmount (RM3000) |
||
|
Dimension |
mm |
in. |
|
Width |
484.0 |
19.0 |
|
Height |
178.0 |
7.0 |
|
Depth |
152.0 |
6.0 |
