Đăng ký nhận chiết khấu độc quyền, cập nhật giá sỉ và tin sản phẩm mới nhất ngay tại hộp thư của bạn.
Bằng cách đăng ký, bạn đồng ý với Điều khoản dịch vụ và Chính sách bảo mật của chúng tôi.
Kết nối trực tiếp với đội ngũ chuyên gia của chúng tôi
Đăng ký nhận chiết khấu độc quyền, cập nhật giá sỉ và tin sản phẩm mới nhất ngay tại hộp thư của bạn.
Bằng cách đăng ký, bạn đồng ý với Điều khoản dịch vụ và Chính sách bảo mật của chúng tôi.
Kết nối trực tiếp với đội ngũ chuyên gia của chúng tôi
Ứng dụng
Lò nung bogie điện RT3-120-14 chủ yếu được sử dụng để xử lý nhiệt các bộ phận kết cấu thép, bộ phận thép đúc, bộ phận thanh trục, sản phẩm thép công cụ, v.v.
Thông số kĩ thuật
Công suất định mức: 120Kw+10%
Nguồn điện: 380V, 3P, 50Hz
Nhiệt độ định mức: 1400℃
Vùng điều khiển: 2 vùng (một vùng cho thân lò, một vùng cho giá chuyển hướng)
Kích thước làm việc: 1500×800×800mm(L×W×H)
Kết nối bộ phận gia nhiệt: Y
Độ đồng đều nhiệt độ: ≤ ± 5℃
Độ chính xác đo nhiệt độ: ± 1℃
Tiêu thụ điện năng lò rỗng: 21KW
Phương pháp kiểm soát nhiệt độ: Tăng nhiệt độ tự động PID; Bộ điều khiển nhiệt độ Huibang với bàn lập trình 60 đoạn, bộ điều chỉnh Shimaden;
Bộ phận gia nhiệt: Thanh silicon cacbua U30
Phương pháp mở cửa lò: Palăng điện lên xuống, bịt kín bằng lò xo
Phương pháp di chuyển Bogie: Bằng bộ giảm tốc
Công suất truyền động của Bogie: 1.1KW
Lớp lót lò: Gạch Mullite
2. Structural Introduction
The RT3-120-14 car bottom furnace is mainly comprised of furnace body, lining, furnace door and door compression system, bogie, heating element, and temperature control system.
2.1 furnace shell
The steel furnace body of the furnace for heat treatment of metals is made from 6-8# sectional steel and 3-14mm steel plates. There is a layer of insulation asbestos board at the furnace shell to reduce the temperature of the shell. The asbestos board is pasted with aluminum silicate fiber cotton with temperature resistance of 1000 degrees, to ensure that the temperature of the shell is less than 50℃.
The heat treat furnace door is electrically lifted upward and downward by the hoist.
The outer surface of furnace shell is treated with environmental painting to make it beautiful.
2.2 furnace lining
2.2.1 The heat treating furnaces and equipment lining is made of 75% AL2O3 mullite bricks;
2.2.2 max temperature of furnace lining is 1400℃.
2.2.3 air hole rate: 5-6%;
2.2.4 thermal conductivity: KcaL/m.h.c>0.9;
2.3 insulating system of furnace body and bogie
The insulation material is close to the outside of the furnace lining and consists of 4 layers.
1st layer: mullite bricks, heat resistance of 1400℃;
2nd layer: light high aluminum bricks, heat resistance of 1250℃;
3rd layer: aluminum silicate fiber cotton, heat resistance of 1100℃;
4th layer: diatomite brick, heat resistance of 900℃;
The layer that is close to the furnace shell is made of fiber cotton and asbestos board, heat resistance of 500-800℃;
All the insulation layer is made of standard bricks with size of 230×113×65mm.
2.4 heating element
2.4.1 the heating element is made of U30 silicon carbide rod;
2.4.2 the heating element is divided into 2 zones.
2.4.3 the heating elements are distributed on both sides of furnace chamber and bogie.
18pcs silicon carbide rods for furnace chamber, 6pcs silicon carbide rods for bogie.
2.5 control cabinet
2.5.1 control zone: 2 zones;
2.5.2 PID automatic and program control;
2.5.3 over temperature power off function, over temperature sound off alarm function;
2.5.4 GGD cabinet with electrostatic spray;
2.5.5 Changzhou Huibang GR858P temperature controller;
2.6 temperature measurement system
2.6.1 the thermal couple is S type, platinum-platinum rhodium core;
2.6.2 sheath of thermal couple: corundum tube;
