Graphtec GL7000 データ収集プラットフォーム | EMIN.VN

Graphtec GL7000 データ収集プラットフォーム

Name: Graphtec GL7000 データ収集プラットフォーム
Brand: GRAPHTEC

メーカーGRAPHTEC(このブランドの他の製品を見る)

ModelGL7000

お問い合わせ

数量

安全なチェックアウト

高品質な対応

簡単な交換・返品

配送対応可能

Manufacturer Graphtec
Model: GL7000

Datasheet

GL7000 main unit specifications

Item		Description
Number of module		Attached to up to 10 modules *1
Number of input channels		Max. 112 channels in one GL7000
External Input/Output signals *2	Input	Start/Stop, Trigger, External sampling, Auto balance Signal type: Contact (relay), Open collector, Voltage
	Output	Trigger, Busy, Alarm (10 channels) *3 Signal type: Open collector (pulled-up by resistor 10 k ohms)
Trigger, Alarm function	Trigger repeat	Enabled (ON): Automatically rearm for the next data capture Disabled (OFF): Data capture is completed in a single trigger
	Trigger action	Start or stop capturing data by the trigger
	Trigger condition	Start: Off, Measured signal, Alarm, External, Clock, Week or Time Stop: Off, Measured signal, Alarm, External, Clock, Week or Time
	Trigger determination conditions for measured signal	Combination: OR or AND condition at the level of signal or edge of signal Analog: Higher/Rising, Lower/Falling, Window-in, Window-out Logic 4: Higher/Rising, Lower/Falling Pulse 4: Higher/Rising, Lower/Falling, Window-in, Window-out
	Alarm determination condition *5	Combination: OR or AND condition at the level of signal or edge of signal Analog: Higher/Rising, Lower/Falling, Window-in, Window-out Logic 4: Higher, Lower, Rising, Falling Pulse 4: Higher/Rising, Lower/Falling, Window-in, Window-out
	Alarm output	10 channels
	Pre-trigger *6	Number of data before trigger: Up to specified number of captured data
Calculation function	Between channels	Addition, Subtraction, Multiplication and Division for two analog inputs (Sampling speed is limited up to 10 Samples/s (100ms interval). Available arithmetic element and the output destination is the analog input channel 1 to 100.)
	Statistical	Select two calculations from Average, Peak, Max., Min. in real time and replay *7
Move function of the display range		Beginning, center or end of the data, Trigger point, Specific time (absolute, relative), Call cursor
Search function		Search for analog signal levels, logic signal pattern, pulse signal levels or alarm point in captured data
Annotation function		Comment can be set in each channel (up to 31 alphanumeric characters)
Message, Marker function		Message: Record up to 8 messages in any timing (Any message can be set before data capture is started or during data capture.)Marker: Recorded when the trigger, alarm or power failure occur
Resume		Resume automatically in the same condition after power is recovered when the power failure occurred duaring data capture *8
Interface to PC		Ethernet (10 BASE-T/100 BASE-TX), USB 2.0 (High speed)
Network function		WEB server, FTP server, FTP client, NTP client, DHCP client
USB drive mode		Emulate the USB memory device *9
Storage device	Built-in	RAM (2 million samples, built-in Signal conditioning module), Flash memory (2 gigabytes, built-in the main module)
	External *10	SD card (Support SDHC, up to 32 GB) slot, SSD (Approx. 64 GB)The file for capturing data is limited up to 2 GB.
Data saving function	Captured data *10	Built-in RAM, Built-in Flash, SD memory card, SSD (Data is saved directly to it.)
	Data in built-in RAM	Specified number of data up 2 million samples increment of 1
	Auto save *10	Available for the built-in RAM Enabled (ON): Data in the RAM is saved automatically to the built-in Flash, SD memory card, SSD Disabled (OFF): Data in the RAM is not maintained after power is turned off
	Ring capturing mode 10 11	Saves most recent data Number of capturing data: 1000 to 2000000 points, Destination of data: Built-in RAM, Built-in Flash, SD memory card, SSD
	During capturing data	Displaying information in two windows, Hot-swapping the SD memory card, Saving data in between cursors.
	Backup *10	Backup interval: Off, 1, 2, 6, 12, 24 hrs. Data destination: SD memory card, SSD, FTP server
Engineering Scale function		Measured value can be converted to the engineering unit Analog voltage: Converts by four reference points (gain, offset) Temperature: Converts by two reference points (offset) Pulse count: Converts by two reference points (gain)
Synchronization between units		Start and Trigger *12
Accuracy of clock (at 23 degree Celsius)		+/- 0.002 % (Monthly deviation approx. 50 sec.)
Operating environment		0 to 45 ºC, 5 to 85 % RH (non condensed)
Power source		100 to 240 V AC, 50/60 Hz
Power consumption		Approx. 85 VA
Standard accessories		Quick guide, CD-ROM, AC power cable
External dimensions (W x D x H)		Main module: Approx. 193 x 141 x 160 mm (Excluding projectin), Alarm output terminal: Approx. 30 x 136 x 145 mm (Excluding projection)
Weight		Main module: Approx. 2 kg, Alarm output terminal: Approx. 350 g

Display module specifications

Model name		GL-Connection
Supported OS		Windows 7 (32/64-bits, Except Starter edition), Vista (32/64-bits), XP *13
Functions		Control GL7000, Real-time data capture, Replay data, Data format conversion
Controlled units		Up to 10 units (Max. 1120 channels)
GL7000 Settings control		Input settings, Memory settings, Trigger and Alarm settings, Other settings
Captured data *14		Built-in RAM (Binary format), Built-in Flash memory (Binary, CSV format), SD memory card (Binary, CSV format), SSD (Binary, CSV format) The sampling is limited by the number of channels used. (1 ms per channel. When 10 channels are set, sampling is limited to 10 ms.)
Displayed information		Analog waveforms, Logic waveforms, Pulse waveforms, Digital values
Display mode		Y-T waveform with digital values, X-Y graph in real time, Cursor information, Capture condition, Alarm information
File operation		Converts binary data to the CSV data (specific period, all data in one file, multiple files), Creates a new file with compression or by consolidating multiple file.
Warning Function		Send e-mail to the specified address when the alarms occur
Statistical calculation		Capturing data: Maximum, Minimum, Peak or Average Replaying data: Maximum, Minimum, Peak, Average or RMS in between cursors
Search function	Level	Specific level in any channel
	Alarm	Occurred alarm in any channel
	Time	Beginning, center, end of the data, Trigger point, Specific time (absolute, relative), Specific number
Operation lock		Operation screen can be locked (It is unlocked with the password.)

Display module specifications

Model name	GL7-DISP
Display device	5.7-inch TFT color LCD monitor (VGA: 640 x 480 dots)
Operation section	Touch panel and Cursor keys *15
Touch panel	Capacitive type touch panel, Operated by finger or the proprietary pen
Displayed language	English, French, German, Chinese, Korean, Japanese
Screen saver	Turns off backlight by 10, 30 sec., 1, 2, 5, 10, 30, 60 min.
Displayed information	Waveform in Y-T with digital values, Waveform only, Digital value, Waveform in X-Y
Connection cable	LAN cable (CAT5 class, Straight connection, Up to 10m) *16
Standard accessories	Bracket for slanted mount, Connection cable (40cm), Ground cable, Screws
External dimensions (W x D x H)	Approx. 187 x 35 x 199 mm (Excluding projection)
Weight	Approx. 530 g

SSD module specifications

Model name		GL7-SSD
Memory device		Solid state disk (SSD), Form factor: 2.5-inch HDD
Capacity		Approx. 64 GB (The file size of the captured data is limited up to 2 GB.)
Sampling speed *17	Attached 1 or 2 modules	Max. 1 M Samples/s
	Attached 1 or 2 modules	Max. 500 k Samples/s
	Attached 5 to 10 modules	Max. 200 k Samples/s
External dimensions (W x D x H)		Approx. 49 x 136 x 160 mm (Excluding projection)
Weight		Approx. 770 g

Excluding the function module as the Display module or SSD module.

The Input/Output cable (B-513) is required for connecting the signal. The Autobalance signal input and the Busy signal output are used in the DC Strain Module.

The alarm signals are output on the terminal block attached to the main module as standard accessory.

It is available on the Logic/Pulse module.

Method of detection Volt./Temp. module: The alarm is detected in the sampling interval when the sampling interval is shorter than 5 seconds. The alarm is detected every 5 seconds when the sampling interval is longer than 5 seconds. Other modules: The alarm is detected in every 1ms when the sampling interval is shorter than 1ms. The alarm is detected in the sampling interval when the sampling interval is set between 2ms to 5 seconds. The alarm is detected every 5 seconds when the sampling interval is longer than 5 seconds.

It is available when the captured data is saved to the built-in RAM. The pre-trigger function may not work in combination with the trigger settings.

The result of real time calculation is displayed in the digital display mode.

When the captured data destination is set to the built-in-RAM, the captured data is not maintained after a power failure occur. The built-in Flash or the SD memory card may be damaged by a power failure if it being accessed to writ data. If the memory device is not damaged, the closed data file is maintained. The file is closed every one minute while data is being captured.

The USB drive mode is started by setting of the switch on the main module. It can be also started when the power is turned on while pressing the key on the display module.

*10

The SD memory card is included as the standard accessory. The SSD module is an option.

*11

The capacity for saving the data is set to one third of available memory when the captured data destination is set to a device other than the built-in-RAM. The sampling speed is limited up to 10 samples (100ms interval).

*12

The Sync cable (B559) is required when this function is used. The GL-Connection software is required when the synchronizing function is used.

*13

The SP2 or higher service pack need to be installed.

*14

The captured data that is saved to the built-in-RAM or SSD cannot be saved to the PC in real time. The data in built-in-RAM or SSD needs to be transferred to the PC after data captur is complete.

*15

Most operations can be selected by both touch panel and keys.

*16

When the display module is mounted at an angle using the bracket, the display module is connected to the main module by a LAN cable that is attached to the display module as standard accessory.

*17

The sampling speed in the GL7000 is limited to the fastest sampling speed of attached signal conditioning module. When the specified sampling speed is faster than the module, the sampling is done in fastest sampling on the module. The same value is stored to the memory device in the specified sampling speed until data is renewed by the next sampling.

Voltage/Temperature Module Specifications

<td style="border:solid windowtext 1.0pt;mso-border-alt:solid windowtext .5pt;

Model number			GL7-M
Number of input channels			10 channels
Input method			All channels isolated balanced input, Scans channels for sampling, Screw terminal (M3 screw)
Sampling speed			100 Samples/s at 1-10ch to 1 Sample/h (10 ms with 1-10ch to 1 hr. interval)
Measurement range	Voltage		20, 50, 100, 200, 500 mV, 1, 2, 5, 10, 20, 50 V, and 1-5 V/F.S.
	Temperature		Thermocouple: K, J, E, T, R, S, B, N, and W (WRe5-26), RTD: Pt100, JPt100 (JIS), Pt1000 (IEC751)
	Humidity *1		0 to 100 % (using scaling function in 5V range, humidity sensor B-530)
Measurement accuracy*2	Voltage		± 0.1 % of F.S.
	Temperature	Thermocouple	Measurement range	Measurement accuracy
		R/S	0 °C ≤ TS ≤ 100 °C	± 5.2 °C
			100 °C < TS ≤ 300 °C	± 3.0 °C
			R: 300 °C < TS ≤ 1600 °C	± (0.05 % of reading + 2.0 °C)
			S: 300 °C < TS ≤ 1760 °C	± (0.05 % of reading + 2.0 °C)
		B	400 °C ≤ TS ≤ 600 °C	± 3.5 °C
			600 °C < TS ≤ 1820 °C	± (0.05 % of reading + 2.0 °C)
		K	-200 °C ≤ TS ≤ -100 °C	± (0.05 % of reading + 2.0 °C)
			-100 °C < TS ≤ 1370 °C	± (0.05 % of reading + 1.0 °C)
		E	-200 °C ≤ TS ≤ -100 °C	± (0.05 % of reading + 2.0 °C)
			-100 °C < TS ≤ 800 °C	± (0.05 % of reading + 1.0 °C)
		T	-200 °C ≤ TS ≤ -100 °C	± (0.1 % of reading + 1.5 °C)
			-100 °C < TS ≤ 400 °C	± (0.1 % of reading + 0.5 °C)
		J	-200 °C ≤ TS ≤ -100 °C	± 2.7 °C
			-100 °C < TS ≤ 100 °C	± 1.7 °C
			100 °C < TS ≤ 1100 °C	± (0.05 % of reading + 1.0 °C)
		N	0 °C ≤ TS ≤ 1300 °C	± (0.1 % of reading + 1.0 °C)
		W	0 °C ≤ TS ≤ 2000 °C	± (0.1 % of reading + 1.5 °C)
		Reference Junction Compensation (R.J.C.) accuracy: ± 0.5 °C *3
		RTD	Measurement range	Driving current	Accuracy
		Pt100	-200 °C to 850 °C (FS = 1050 °C)	1 mA	± 1.0 °C
		JPt100	-200 °C to 500 °C (FS = 700 °C)	1 mA	± 0.8 °C
		Pt1000