EMIN Organizes a Picnic for Company Employees

As part of the annual activities of EMIN Joint Stock Company, the aim is to create a common playground, develop physical fitness and build team spirit among the company's employees. On October 5, 2024, EMIN GROUP organized a picnic for all employees and families in Ban Xoi Valley in Ba Vi.

Some details about Ban Xoi Valley

Ban Xoi Valley belongs to the Ba Vi tourist complex, located in Xom Chong, Yen Bai commune, Ba Vi. The space here is extremely large with rolling hills and rippling lakes, very suitable for picnic activities at this time.

EMIN's picnic activities

The theme for this year's picnic activity of EMIN GROUP is "CONNECTING STRENGTH, CONNECTING SUCCESS". The company's Board of Directors wishes to cooperate and unite the spirit of teamwork to help the company achieve more success in the future.

Departure time starts at 11:00 a.m. on October 5, 2024 at EMIN Hanoi and arrives at Ban Xoi valley at about 12:00 p.m. After resting, the whole group enjoyed an extremely delicious meal with specialties such as Muong lam rice, stir-fried baby veal, steamed veal, goat porridge, roasted wild boar, beef with wine sauce, wormwood leg, hill chicken. ,...

After lunch, recreational activities take place such as boating, photography, fishing, visiting and learning about the village, etc.

In order to encourage employees' spirit with the spirit of "Playing is the best", the company's Board of Directors organizes a Kayak race, and will also award prizes to employee duos participating in the Kayak race that rank 1st, 2nd, 3.

At night, after dinner ends, fun activities around the campfire begin to take place. Everyone played together, sang and wished happy birthday to the pink shadows of October

Below is a series of fun and rewarding activities to encourage the spirit of solidarity among employees:

관련 뉴스

2026년 07월 09일 14시 40분 30초

Distinguishing Between DFT and WFT in Coating Thickness Measurement

Many projects encounter a situation where a freshly applied coating looks perfectly uniform and paint consumption matches the estimate, yet additional coating is required during inspection because the thickness is insufficient. This leads many to suspect measurement errors or equipment inaccuracy, whereas the actual cause is a confusion between WFT (Wet Film Thickness) and DFT (Dry Film Thickness)

2026년 07월 08일 16시 56분 01초

Can a car paint thickness gauge detect if a vehicle has been in a collision?

Many used car buyers often spend a considerable amount of time examining the paintwork, the gaps between body panels, or the overall condition of the exterior. However, these signs can be skillfully masked following repairs; precise color matching and careful polishing can make the vehicle appear almost factory-original.

2026년 07월 08일 14시 20분 39초

Latest fire-retardant coating thickness standards for steel structures (DFT, WFT & acceptance procedures

A fire-retardant coating only provides effective protection when applied to the specified design thickness. A shortfall of even a few hundred microns can significantly reduce fire resistance, whereas an excessively thick coating is prone to cracking and peeling, in addition to increasing material costs

2026년 07월 07일 10시 35분 50초

Is Ultrasonic Welding Waterproof? Find out with the experts!

Water resistance is a common requirement for a wide range of modern products, spanning industrial sensors, outdoor LED lights, medical devices, and water filter cartridges to electronic components and automotive parts. When exploring manufacturing technologies, many businesses often ask the same question: can ultrasonic welding truly create a watertight seal?

2026년 07월 07일 09시 47분 07초

Why Is the Ultrasonic Weld Not Airtight? Causes and Solutions

A satisfactory ultrasonic weld must form a uniform bond across the entire contact surface. The presence of gaps, edge separation, or partial adhesion significantly compromises airtightness, watertightness, and mechanical strength. This is a common issue in the manufacturing of plastics, electronic components, packaging, and medical devices, particularly following a product changeover or an adjustment of welding parameters on the production line.