EMC testing solutions for electric vehicles under real operating conditions

As you can see, the reality of electric vehicles is increasingly modern, and EMC testing is increasingly complex. Therefore, Rohde & Schwarz, in collaboration with AVL, has developed a comprehensive EMC testing solution for electric vehicles in dynamic conditions, meeting all requirements beyond the action standards. Let's follow the article below!

EMC in electric vehicles: new problems from new powertrains

The shift from internal combustion engine (ICE) vehicles to electric vehicles (EV) is not only a change in powertrain technology, but also entails a series of new electronic systems: such as HV battery packs, inverters, electric motors, ECUs, and all of which are potential sources of electromagnetic interference (EMI).

In particular, inverters are the strongest EMI-causing components due to their high switching frequencies and high voltages. When EVs use new technologies such as GaN inverters, the noise level can be 10 times higher than that of traditional IGBTs. These noises affect safety systems such as radar, cameras, and lidar sensors in ADAS, making EMC testing a mandatory requirement.

EMC testing under dynamic driving conditions

Most current EMC standards, such as CISPR 12 or CISPR 25, only require vehicles to operate at a fixed speed (e.g. 40 km/h). But in reality, electric vehicles operate continuously in many different modes: acceleration, deceleration, recharging, driving on slopes, city streets, highways, etc.

Lab measurements that do not adequately simulate these conditions will have difficulty detecting dangerous noise peaks, making the system susceptible to failure in real-world environments.

For example, the same car running at 40 km/h and 120 km/h will give completely different noise emission results, in many cases exceeding the standard threshold when entering dynamic mode.

The problem is: synchronizing test bench and measurement software

To test EMC under dynamic conditions, it is not possible to use only conventional measuring equipment. Enterprises need a test bench capable of accurately simulating the operating states of the vehicle: changing torque, increasing speed, recharging conditions, ambient temperature, etc.

However, a big challenge is how to synchronize these technical parameters with the EMC measuring software, so that the measurement takes place at the right time, at the right load conditions with the highest risk of generating interference.

Rohde & Schwarz and AVL Combined Solution: Unified EMC Test Platform

To address all of the above issues, Rohde & Schwarz has teamed up with AVL - a leading expert in simulation and dynamic testing - to develop a unified EMC test platform for real-world electric vehicle operating conditions.

System structure includes:

Rohde & Schwarz EMC system: R&S®ELEKTRA software, EMI receiver, generator, antenna, turntable

AVL PUMA test bench: simulation of motors, torque, batteries, environmental conditions, heat cabinets...

Common control interface: automatic synchronization between two software, no need for separate operation.

Outstanding features:

- Real-time synchronization of parameters: speed, torque, voltage, current, temperature...

- Detailed noise spectrum analysis according to each load condition

- Accurately determine dangerous noise frequencies and arising conditions

- Run automatic tests according to standard profiles: WLTC, NEDC, J10...

- Export full reports, easy to compare and analyze

Practical application: Full-process synchronous EMI/EMS testing

- With this system, engineers can:

- Plan EMC tests according to acceleration/deceleration cycles

- 2-way communication between PUMA and ELEKTRA to trigger measurements at the right time of high risk

- Monitor real-time noise spectrum

- Compare results between EMS modes on/off, with/without load to determine the actual impact

Refer to the document and learn more about the solution at:

관련 뉴스

2026년 11월 14일 11시 35분 16초

What Is Fiber Polarity and How Do You Choose an MPO Method?

Fiber polarity ensures the transmit path connects to the corresponding receive path. For MPO-based duplex channels, the selected method must remain consistent across trunks, cassettes, adapters, and patch cords.

2026년 11월 14일 10시 28분 19초

The scent of new wood in a newly handed-over apartment: How to measure and address formaldehyde (HCHO) levels before moving in

Many people refer to the pungent, acrid odor that emerges when opening a new cabinet as the "smell of new wood," assuming it will simply dissipate after a few days. In reality, however, what is being released could well be formaldehyde—a substance originating from the adhesives used in the pressed-wood panels—and our sense of smell is not a reliable enough gauge to determine the concentration levels present

2026년 11월 13일 17시 23분 39초

Guide to Selecting a TCLP Toxicity Characteristic Leaching Procedure Shaker Configuration in Compliance with QCVN 07:2025/BNNMT and TCVN 9239:2012

Regulation QCVN 07:2025/BNNMT (replacing QCVN 07:2009/BTNMT and QCVN 50:2013/BTNMT) specifies hazardous waste and sludge thresholds based on leachate concentrations. To ensure that analytical results for heavy metals and organic compounds are accepted during ISO/IEC 17025 or VIMCERTS assessments, laboratories must comply with the Toxicity Characteristic Leaching Procedure (TCLP) specified in TCVN 9239:2012, which is equivalent to US EPA Method 1311

2026년 11월 13일 16시 11분 22초

Checking the Temperature of Paint and Coating Surfaces After Curing Using an Infrared Thermometer

An infrared thermometer allows surface temperature measurement without direct contact, making it suitable for products coming out of curing ovens or surfaces that are difficult to access. However, to ensure reliable results for production quality control, it is important to understand the measurement principle and the factors that affect measurements on painted and coated surfaces.

2026년 11월 13일 15시 07분 40초

Crowded Gyms and Yoga Studios: How to Manage Air Quality to Retain Members

Around 6 or 7 in the evening, the gym becomes packed; the music drowns out the sound of heavy breathing, and the air conditioning runs at full blast behind closed doors. At first glance, everything seems fine: the room is cool, the lights are bright, and the equipment is state-of-the-art. Yet, after just a few sessions, regular members begin to feel a heavy-headedness and find themselves running out of breath more quickly eventually, they simply stop renewing their memberships. No one complains about the personal trainers or the exercise machines. The very thing that makes them feel stifled and drives them away is something entirely invisible: the air inside the room