For full functionality of this site it is necessary to enable JavaScript.
EMIN.VN
0

Hội thảo Diễn đàn đo lường Keysight (KMF) 2024

2024년 11월 21일 13시 53분 18초

Ngày 15/11/2024 vừa qua, EMIN GROUP và 3 đơn vị MITAS, ASIC, NDV phối hợp cùng Keysight tổ chức hội thảo Diễn đàn đo lường Keysight (KMF) tại khách sạn JW Marriott Hà Nội

Keysight Measurement Forum (KMF) is an important event of Keysight Technologies held across Southeast Asia to share technology trends and innovations in the industry. This forum brings new knowledge about 6G technology, advanced circuit design, and high-speed digital. This is a place that connects businesses and experts in the electronics and semiconductor value chain, striving to find solutions for field inspection areas.

Since November 2014, Keysight Technologies is a subsidiary separated from Agilent Technologies, officially operating with full functions and authority to operate the electronic measurement equipment segment of the former Agilent. From here, all product names, documents, and certifications bearing the Agilent brand name were renamed Keysight.

And since November 2020, EMIN has officially become a direct distributor of Keysight in Vietnam.

At the conference, leading experts from Keysight shared about breakthroughs in the fields of 5G, 6G, Semiconductor Circuit Design and High-Speed ​​Digital Technology. In addition, attendees will also have a hands-on experience with many of Keysight's most advanced equipment in the showroom area, including the exhibition booths of EMIN Group and other partners.

During the organization, the EMIN GROUP team and Keysight's senior experts are pleased to bring you the latest updated knowledge in the field of measurement and testing such as 6G and 5G connection technology. NTN, High Speed ​​Digital and Semiconductor Circuit Design.

Once again, EMIN GROUP would like to sincerely thank you for your interest in attending the event.

Below are the images we captured at the conference:

관련 뉴스

Comparing Shore A and Shore D Hardness: Two Common Hardness Scales Today
2026년 08월 10일 14시 16분 08초

Both Shore A and Shore D are used to measure material hardness, but each scale is suited to a different group of materials. Soft rubber, silicone, or elastic gaskets are typically tested using Shore A, whereas hard plastics, engineering plastics, and materials with low deformation are better suited to Shore D

What causes equipment to restart automatically in the factory, and how can the fault be identified?
2026년 08월 10일 11시 17분 47초

Equipment restarts in a factory setting can be attributed to voltage sags, momentary power outages, electrical noise, overheating, or hardware faults. For incidents that last only a few power cycles, a power quality analyzer can capture voltage, current, and waveform data at the exact moment of the reset, thereby helping engineers determine whether the power supply is the cause

Why Measured Amplitude Is Lower Than the Real Value
2026년 08월 10일 09시 28분 50초

An oscilloscope can display a lower amplitude than the true signal when its bandwidth is not high enough. This article explains bandwidth, the 5x rule, and rise time in practical terms.

Why Measured Amplitude Can Be Lower Than the Real Value
2026년 08월 10일 09시 27분 59초

An oscilloscope can display a lower amplitude than expected when its bandwidth is too limited for the signal being measured. This article explains the relationship between bandwidth, rise time, and measurement accuracy.

혜택 소식 받아보기

대량 할인, 도매 가격 업데이트 및 신제품 소식을 이메일로 받아보세요.

구독하면 당사의 서비스 이용약관개인정보 처리방침에 동의하는 것으로 간주됩니다.

빠른 지원

인증된 전문가에게 직접 연결