How to connect a flow switch

## What is a Flow Switch? **_[Flow switches][1]_**, also known as flow control switches, are devices used to detect and monitor the presence or flow rate of

What is a Flow Switch?

Flow switches, also known as flow control switches, are devices used to detect and monitor the presence or flow rate of liquids or gases in pipelines. When the flow rate exceeds or falls below a set value, the switch triggers an ON/OFF signal to a control system such as a PLC, pump control panel, or alarm. Flow switches play a crucial role in flow monitoring, protecting equipment such as pumps, increasing operational efficiency, and ensuring system safety.

Principle of Operation of Flow Switches

Flow Detection:

The device uses mechanical or electronic sensors to detect the flow of liquids or gases in the pipeline.

ON/OFF Signal:

When the flow rate reaches the set threshold, the switch changes the contact state (closed or open) to send a signal to the controller or other device.

Common Types of Flow Switches

1. Mechanical Flow Switches

Fan-type and piston-type flow switches.

Advantages: Low cost, easy installation.

Disadvantages: Lower accuracy compared to electronic types.

2. Electronic Flow Switches

Uses electronic sensors for more accurate flow detection.

Suitable for highly automated systems, better sensitivity, and less maintenance.

See product catalog at: EMIN Flow Switches

Applications of Flow Switches in Practice

Pump and equipment protection: Flow switches will shut off the pump when there is no fluid flow, preventing dry running and damage.

HVAC and fire protection systems: In HVAC and fire protection systems, water quality monitoring devices trigger alarms when water flows through the sprinkler system.

Applications in production lines and water treatment: Water flow meters; flow rate and velocity monitoring devices for gasoline, oil, chemicals, and wastewater.

Instructions for Wiring a Flow Switch

Before connecting the flow switch, ensure the power supply is off and the fluid valve is turned off.

Step 1: Prepare the installation location

Choose a suitable pipe location (horizontal or vertical).

Ensure the pipe is clean and does not obstruct the flow.

Step 2: Attach the switch to the pipe

Use a T-fitting or threaded connector to attach the switch.

관련 뉴스

2026년 07월 10일 15시 42분 44초

[EMINxKeysight] International Electronics & Smart Manufacturing Exhibition 2026

EMIN and Keysight sincerely thank you for taking the time to attend the 2026 International Electronics & Smart Manufacturing Exhibition in Dong Anh

2026년 07월 10일 15시 10분 46초

What Is Resonant Frequency? Why Can a Single Frequency Range Damage the Entire Product?

A device may operate stably for months, yet suffer cracks, broken solder joints, or snapped component leads after being transported. What surprises many engineers is that the vibration amplitude during transport is no greater than usual. The root cause lies in a specific frequency range where the product's structure absorbs energy most intensely, triggering resonance and causing continuous stress concentration at a single point.

2026년 07월 10일 10시 38분 40초

Should Carton Packaging Undergo Vibration Testing or Drop Testing First?

Một kiện hàng gần như không bao giờ bị rơi ngay khi vừa rời khỏi nhà máy. Quãng đường hàng trăm kilomet trên xe tải, container hay băng chuyền mới là giai đoạn diễn ra đầu tiên, nơi bao bì liên tục chịu rung lắc trong nhiều giờ. Chỉ sau đó mới đến những cú va chạm khi bốc xếp, giao nhận hoặc rơi ngoài ý muốn.

2026년 07월 09일 14시 40분 30초

Distinguishing Between DFT and WFT in Coating Thickness Measurement

Many projects encounter a situation where a freshly applied coating looks perfectly uniform and paint consumption matches the estimate, yet additional coating is required during inspection because the thickness is insufficient. This leads many to suspect measurement errors or equipment inaccuracy, whereas the actual cause is a confusion between WFT (Wet Film Thickness) and DFT (Dry Film Thickness)

2026년 07월 08일 16시 56분 01초

Can a car paint thickness gauge detect if a vehicle has been in a collision?

Many used car buyers often spend a considerable amount of time examining the paintwork, the gaps between body panels, or the overall condition of the exterior. However, these signs can be skillfully masked following repairs; precise color matching and careful polishing can make the vehicle appear almost factory-original.