For full functionality of this site it is necessary to enable JavaScript.
EMIN.VN
0

SMEMA standard for PCB conveyors

2026년 11월 16일 14시 00분 39초

SMEMA was developed to address this specific point; consequently, conveyors, loaders, and unloaders all include an SMEMA port in their technical specifications

IPC SMEMA 9851 STANDARD

SMEMA Standard on PCB Conveyors

When a conveyor pushes a PCB forward before the downstream machine is ready, two boards overlap at the junction, scratching components or jamming the track. This issue occurs on any SMT line linking multi-vendor equipment without coordinated signaling. SMEMA was created specifically to prevent this bottleneck—which is why conveyors, loaders, and unloaders all list SMEMA ports in their specifications.

What Is SMEMA and What Does IPC SMEMA 9851 Define?

SMEMA stands for Surface Mount Equipment Manufacturers Association, founded in 1984 by North American equipment makers and merged into IPC in 1999. The current revision, IPC SMEMA 9851, was published in February 2007, replacing SMEMA 1.2.

SMEMA Protocol
1984SMEMA association founded
1999Merged into IPC
2007IPC SMEMA 9851 replaced SMEMA 1.2

The standard consists of two parts. The mechanical section defines pass height, fixed rail location, and conveyor width. The electrical section defines handshake signals between adjacent machines. This enables a solder paste printer from brand A, a conveyor from brand B, and a pick-and-place machine from brand C to operate together on one line without manual board transfers.

How SMEMA Works: Board Available and Machine Ready Signals

SMEMA uses physical signal cables connecting machines via a 14-pin interface without transmitting complex data. The handshake revolves around two mandatory signals between the upstream and downstream machines.

  1. The upstream machine finishes processing, holds a PCB at its exit, and sends the Board Available signal.
  2. The downstream machine is empty and responds with the Machine Ready signal.
  3. Only when both signals are active does the conveyor motor run to transfer the PCB to the next stage.
  4. Once the board passes the sensor, the signals reset and both machines wait for the next cycle.

In addition to these two signals, SMEMA includes an optional Failed Board Available signal. This allows downstream conveyors to divert defective PCBs after AOI or SPI off the main line without halting production.

How Does the SMEMA Standard Benefit an SMT Line?

Prevents Board Accumulation & Collisions

Conveyors hold boards until the downstream machine finishes its previous cycle, preventing track jams and component scratches at transfer points.

Multi-Vendor Equipment Integration

Anda, Censtar, I.C.T, and Suneast conveyors integrate directly into existing SMT lines thanks to shared mechanical and electrical standards.

Continuous Line Automation

The entire line—from entry loading through processing stages to exit unloading—runs continuously without manual operator intervention.

How Does SMEMA Differ From Hermes, and Should Your Factory Upgrade?

Hermes (IPC HERMES 9852) is the successor to SMEMA, released in April 2017 and recognized by IPC in 2018. The difference lies in data richness: SMEMA only communicates "board present" and "ready to receive," whereas Hermes also transmits unique board identifiers so lines do not need barcode scanners at every station. According to the Hermes standard group, newer Hermes equipment can run alongside legacy SMEMA-only machines.

Most SMT conveyors today still come equipped with SMEMA ports by default—making SMEMA compatibility the first item to verify when integrating a conveyor into an existing line.

What to Verify When Selecting a SMEMA-Compatible Conveyor

Matching SMEMA ports only solves electrical signaling. Mechanical alignment determines whether PCBs travel straight between machines—engineering and purchasing teams should verify four key points.

Conveyor Pass Height

The standard specifies an adjustable transport height from 940 mm to 965 mm measured from the floor to the PCB underside. Because 900 mm ± 20 mm still appears on many conveyors, measure the actual height of each machine on your line and level all units with adjustable feet.

Flow Direction

Confirm whether your line runs left-to-right (L to R) or right-to-left (R to L), and configure SMEMA send/receive directions accordingly.

Fixed Rail Side

The standard defines the front rail as the fixed reference rail. If your existing line uses a rear fixed rail, order a matching conveyor configuration so PCBs stay centered between machines.

Failed Board Signal

Lines equipped with AOI or SPI require conveyors supporting this optional signal—verify availability before placing an order.

Read more:
Reducing PCB Scratches and Drops During Stage Transfers in SMT Assembly Lines

SMEMA-Compatible Conveyors at EMIN

EMIN supplies PCB handling and transport equipment supporting SMEMA connectivity, categorized by line function.

Factories adding conveyors to an existing SMT line can contact EMIN's engineering team with your flow direction, fixed rail position, and adjacent conveyor heights for compatibility verification and a detailed quote.

Integrating a New Conveyor Into Your Existing SMT Line?

Send your flow direction, fixed rail side, and adjacent machine pass heights—EMIN's engineering team will verify compatibility and provide a detailed quote.

Request Compatibility Check →

Frequently Asked Questions

What is SMEMA?

An interface standard for SMT equipment covering both mechanical dimensions and electrical handshake signals, allowing machines from different manufacturers to transfer PCBs on the same line.

Can conveyors from different manufacturers be connected together?

Yes, provided pass height, flow direction, and fixed rail alignment match. SMEMA handles electrical signaling, while mechanical dimensions must be verified separately.

Does SMEMA transmit PCB tracking data?

No. SMEMA only sends electrical signals indicating board availability and machine readiness. Board ID data transmission falls under the Hermes standard.

Is the Failed Board signal mandatory?

No, it is an optional signal used to automatically divert defective boards off the main production line.

관련 뉴스

Reduce scratches and drops of PCB boards during transfer between stages in an SMT production line
2026년 11월 16일 10시 42분 38초

In a well-functioning SMT line, when QC detects defects at the end of the process, the immediate assumption is often that the issue lies with the solder paste printer or the component placement machine. However, upon closer investigation, there are certain types of defects that cannot be attributed to any single specific stage. Read the article below to learn more!

Homes on busy streets: How to measure fine particulate matter and exhaust fumes entering your living room
2026년 11월 16일 09시 42분 31초

Living in a house facing a main road is particularly frustrating: you might wipe the tables until they’re spotless in the morning, only to find them covered in a layer of dust by the afternoon. Even with the doors tightly shut and the curtains drawn, the house still feels stuffy by evening—permeated by the faint, lingering presence of vehicle exhaust. While regular dust can be swept away, fine particulate matter the kind you can’t even see silently seeps in through the gaps around your doors and windows. So, before you rush to spend money on an air purifier or weather-stripping, take a moment to check the current air quality inside your home and identify exactly where the pollutants are entering

When Should You Use Stick, TIG, or MIG Welding?
2026년 11월 16일 08시 47분 55초

Stick welding uses a coated electrode without shielding gas; TIG prioritizes clean, precise welds; MIG supports continuous wire feeding and easier automation.

What Are 10 Common MIG Welding Problems and Fixes?
2026년 11월 16일 08시 47분 05초

Common MIG welding faults often trace to shielding gas, polarity, wire feeding, torch condition, joint preparation, welding settings, or cable connections. Match the symptom to its likely checks before changing parts.

What Safety Rules Apply When Using a Plasma Cutter?
2026년 11월 16일 08시 46분 16초

Safe plasma cutting depends on protection from heat, arc light, electrical hazards, fumes, and gas-system risks. Keep combustibles at least 10 m away and inspect cables, torch parts, grounding, PPE, and gas equipment before work.

혜택 소식 받아보기

대량 할인, 도매 가격 업데이트 및 신제품 소식을 이메일로 받아보세요.

구독하면 당사의 서비스 이용약관 및 개인정보 처리방침에 동의하는 것으로 간주됩니다.

빠른 지원

인증된 전문가에게 직접 연결