快速支持
直接联系认证专家
Tough, impact, waterproof and dust resistant equivalent to IP54
Measurement Mode: PE, IE & EE
Measurement Rate:
+ 4 readings per second
+ 32 readings per second
+ 6 readings per second
Thickness Range:
+ PE (contact) on steel: 1.000 - 254mm (0.040 - 10.000 inches)
+ PE (contact) on plastic: from 0.254mm (0.010 inches)
+ IE on steel: 1.27 - 25.4mm (0.050 - 1.000 inch)
+ IE on plastic: from 0.127mm (0.005 inches)
+ EE (contact) on steel: 2.54 - 76.20mm (0.100 - 3.000 inches) -
+ EE on steel: 0.15 - 12.70mm (0.006 - 0.500 inches)
Measurement Accuracy: ±1% or ±0.02mm
Measurement Units: mm or inches
Selectable Reading Resolution: 0.01mm / 0.001mm
Calibration Options: Single, two point, velocity & material type
Datalogging: 2,000 readings
RS232 Interface: Bi-directional
Battery Type: 3 x AA alkaline
Battery Life (approximate): 150 hours
Operating Temperature: -10 to 60ºC (14 to 140ºF)
Size (w x h x d): 63.5 x 165.0 x 31.5mm (2.5 x 6.5 x 1.24 inches)
Weight (including batteries): 383g (13.5oz)
RS232 Interface: Bi-directional
Packing List: Elcometer NDT PG70ABDL precision gauge, couplant, carry case, user manual, test certificate, 3 x AA batteries, software, transfer cable
Note: A transducer is not suppied with the Gauges, must be ordered separately
The auto find feature locates the detection point(s) and adjusts the display settings to bring the waveform into view.
The high speed scan feature on the PG70ABDL precision thickness gauge speeds up the inspection process by taking 32 measurements per second. Remove the transducer from the test material and display the minimum measurement scanned.
Visual and audible alarm with high and low limit settings for specific application tolerances.
Features:
PG70ABDL Precision Thickness Gauge
Technical Specification
|
Model & Part Number |
PG70ABDL |
|
Material thickness digits display |
■ |
|
B-Scan cross sectional display |
■ |
|
Combined B-Scan and digits display |
■ |
|
Scan bar display |
■ |
|
A-Scan display |
+ Rectified, - Rectified, Full Waveform (RF) |
|
PE, IE & EE (ThruPaint™) |
|
|
Measurement Rate: |
|
|
Measuring Range |
PE (contact) on steel: 1.000 - 254mm (0.040 - 10.000 inches) |
|
Measurement Accuracy |
±1% or ±0.02mm whichever is the greater |
|
Measurement Resolution |
User selectable: 0.01mm / 0.001mm (0.001 / 0.0001 inch) |
|
Velocity Calibration Range |
1250 - 10,000m/s (0.0492 - 0.3936in/ms) |
|
High speed scan mode |
■ |
|
Differential mode |
■ |
|
Limit alarm mode |
■ |
|
Selectable resolution |
■ |
|
B-Scan display speed |
15 seconds per screen |
|
Calibration setups |
16 factory & 48 user-definable setups transferrable to and from a PC archive |
|
Gates |
• PE: 1 gate; IE, Plastic & EE: 1 gate with hold off |
|
Pulser type |
Square wave pulser with adjustable pulse width (spike, thin, wide) |
|
Gain |
Manual or automatic gain control (AGC) with |
|
Timing |
40MHz with ultra low power 8 bit digitizer |
|
Data logging |
• 12,000 readings with waveforms |
|
Calibration Options |
Single, two point, velocity & material type |
|
Transducer Probe Type |
Single element with delay tip, pencil with delay tip & contact probes |
|
Transducer Frequency Range |
1 - 20MHz |
|
Transducer recognition |
Manual - selectable from a list |
|
V-path / dual path error correction |
Automatic |
|
Probe zero |
Manual (via integrated probe disk) |
|
Display |
1/8" VGA (grayscale), 62 x 45.7mm (2.4 x 1.8inch) viewable area |
|
Units (selectable) |
mm or inches |
|
LED Backlight |
on / off / auto |
|
Repeatability / Stability Indicator |
■ |
|
Battery Type |
3 x AA alkaline |
|
Battery Life (approximate) |
150 hours |
|
Low Battery Indicator |
■ |
|
Battery Save Mode |
auto |
|
Operating Temperature |
-10 to 60ºC (14 to 140ºF) |
|
Size (w x h x d) |
63.5 x 165.0 x 31.5mm (2.5 x 6.5 x 1.24 inches) |
|
Weight (including batteries) |
383g (13.5oz) |
|
Aluminium case design with gasket sealed |
■ |
|
Transducer Connector Type |
LEMO |
|
RS232 Interface |
Bi-directional |
|
Packing List |
Elcometer NDT PG70ABDL precision gauge, couplant, carry case, user manual, |
