快速支持
直接联系认证专家
CMRR: 120 dB
NMRR: 60 dB
Width: 96 mm
Height: 48 mm
Length: 127 mm
Tuning: Autotune
Weight: 295 g
Accuracy: ± 0.03 %
Polarity: Unipolar
Approvals: UL, C-UL, UKCA, CE per EN61010- 1:2001, F
Isolation: Isolation Power to Input/Output: 2300 Vac per 1 minute test For Low Voltage Power Option: 1500 Vac per 1 minute test Power to Relay/SSR Output: 2300 Vac per 1 minute test Relay/SSR to Relay/SSR Output: 2300 Vac per 1 minute test RS232/485 to Input/Output: 500 Vac per 1 minute test
Input Type: mA, Voltage, Strain
Resolution: 10/1µV
Form factor: 1/8 DIN Horizontal
Control Mode: PID Control, On-off control
Current, Max: 0 to 20 mA (5 Ω load)
Display Size: 46 mm (1.8 in)
Display Type: 4 Digit LED
Accuracy Note: 0.03% reading
Input Voltage: 0 to 100 mVdc, -100 mVdc to 1 Vdc, 0 to 10 Vdc
Output Detail: Pulsed 10 Volts at 20 mA, Relay SPDT 3A at 120/3 A at 240 Volts & Alarm;Control Output 1 and 2 Relay: 250 Vac or 30 Vdc @ 3 A (resistive load); configurable for on/off, PID and ramp and soak Output 1: SPDT, can be configured as alarm 1 output Output 2: SPDT, can be configured as alarm 2 output SSR: 20 to 265 Vac @ 0.05 to 0.5 A (resistive load); continuous DC Pulse: Non-isolated; 10 Vdc @ 20 mA Analog Output (Output 1 Only): Non-isolated, proportional 0 to 10 Vdc or 0 to 20 mA; 500 52 max Output 3 Retransmission Isolated Analog Voltage and Current Current: 10 V max @ 20 mA output Voltage: 20 mA max for 0 to 10 V output
Output Signal: None
Ramp Setpoint: Ramp to Setpoint: 00.00 to 99.59 (HH:MM), or OFF
Ramp and Soak: Single Ramp & Soak
Sampling Rate: 3 Hz (3 updates/second)
Step Response: 0.7 sec for 99.9%
A/D Conversion: Dual Slope
Analog Current: 0 to 20 mA (500 Ω maximum)
Control Output: SSR Relay
Data Interface: Ethernet, RS485, RS422, RS232
Digital Filter: Programmable
Supply Voltage: 90 to 240 Vac
Impedance Input: 10 MΩ for 100 mV; 1 MΩ for 1V or 10 Vdc
Remote Setpoint: None
Span Adjustment: 0.001 to 9999 counts
Measurement Type: Current, Strain, Voltage
Number of Inputs: 1
Cutout Dimensions: 45 x 92 mm
Decimal Selection: 0,001, 0,01, 0,1, None
Display Type Note: 4-digit 9-segment LED 10.2 mm (0.40"); i32, i16, i16D, i8DV 21 mm (0.83"); i8 10.2 mm (0.40") and 21 mm (0.83"); i8DH RED, GREEN, and AMBER programmable colors for process variable, setpoint and temperature units
Enclosure Ratings: None
Offset Adjustment: -1999 to 9999
Supply Power Note: 90 to 240 Vac ± 10%, 50 to 400 Hz*, 110 to 375 Vdc, equivalent voltage; Excitation Voltage Note-24 Vdc @ 25 mA (not available for low-power option)
Supply Power Type: AC
Thermocouple Type: None
Data Interface Note: Ethernet: Standards compliance IEEE 802.3 10 Base-T Supported Protocols: TCP/IP, ARP, HTTPGET RS232/RS422/RS485: Selectable from menu; both ASCII and MODBUS protocol selectable from menu; programmable 300 to 19.2 Kb; complete programmable setup capability: program to transmit current display, alarm status, min/max, actual measured input value and status. RS485: Addressable from 0 to 199
Input Configuration: Single-ended
Linearization Points: Up to 10
Set Point Adjustment: Menu Configurable
Additional Features 1: Programmable 3 Color Display
Electrical Connection: Screw Terminal
Temperature Stability: Temperature Stability: RTD: 0.04°C/°C; TC @ 25°C (77°F): 0.05°C/°C ; Cold Junction Compensation Process: 50 ppm/°C
Control Characteristics: Control Action: Reverse (heat) or direct (cool) Rate: 0 to 399.9 s Reset: 0 to 3999 s Cycle Time: 1 to 199 s; set to 0 for on/off Gain: 0.5 to 100% of span; setpoints 1 or 2 Damping: 0000 to 0008 Soak: 00.00 to 99.59 (HH:MM), or OFF
Isolated Analog Voltage: 0 to 10 Vdc (max 20 mA)
Number of Control Outputs: 2
Cold Junction Compensation: 50 ppm/°C
Thermocouple Lead Resistance, Max: 100 Ω
