Digimatic Caliper Calibration Procedure

**INSTRUCTION**** ** ** ** **1\. Range of application** This technical document specifies the calibration of digimatic calipers with up to 600 mm in me

INSTRUCTION

1. Range of application

This technical document specifies the calibration of digimatic calipers with up to 600 mm in measuring range and 0.01 mm resolution.

2. Calibrating techniques

- Outside check

- Technical check

- Measurement check

3. Calibrating instruments
3.1 Standard measuring instrument (s)
Caliper checker:
- Range of Measurement: (20 ÷ 300) mm
(20 ÷ 600) mm

- Accuracy: ± 5 µm (L ≤ 300 mm)

± 7 µm (L > 300 mm)

3.2 Other measuring instrument (s)

Inside and Outside Micrometer:

- Range of Measurement: (0 ÷ 25) mm

(5 ÷ 30) mm

- Resolution: 0.001 mm

- Accuracy: ± 1 μm

± 5 μm

3.3 Supporting instrument (s)

Hygro-Thermometer:

EXTECH 445814 Hygro-Thermometer Humidity Alert with Dew Point

- Range of Measurement: (0 ÷ 50) °C

- Accuracy: ± 0,5 °C

- Range of Measurement: (10 ÷ 95) %RH

- Accuracy: ± 3 %RH

4. Auxiliary Instrument(s)

- Specialized cleaning solution and towel

5. Conditions for Calibration

- Temperature: (23 ± 5) °C

- Humidity: no higher than (50 ± 15) %RH

6. Prepare for Calibration

Prior to the calibration, the following preparations must be done:

- Prepare the standard instrument

- Select the suitable standard instrument to calibrate the caliper.

- Use the cleaning solution and specialized wipes to clean the surface of the standard instrument.

- Place standard instruments in the calibration room for temperature stabilization for at least two hours.

Prepare the caliper to be calibrated:

- Clean the caliper and its jaws with industrial gasoline or equivalent solvents.

- Place the caliper near the standard instrument in the calibration room for at least two hours to stabilize the temperature before performing the calibration.

7. Begin the calibration

7.1 Outside Check

7.2 Technical Check

7.3 Measurement Check

7.3.1 Identify the accuracy of the caliper

- Outside measurement

- Inside Measurement

7.3.2 Check the deviation of the jaw

- Outside jaws

- Inside Jaws

8. Reliability Evaluation

9. General handling

a. The calibrated caliper is stamped, certified in paper along with calibration results, and measurement uncertainty.

b. The recommended calibration cycle of digimatic caliper is 12 months.

10. About EMIN's Calibration - Verification - Repair center

EMIN Vietnam’s Calibration and Verification center has been established since 2020 to provide after-sales services. The Calibration and Verification center is thoroughly equipped with technical equipment, followed by the assistance from various equipment manufacturers around the globe. At the center, calibration of specialized equipment is successfully carried out by experienced engineers in EMIN Vietnam, ensuring fast, accurate, reliable procedure to meet the most demanding customers’ requirements). Such technical capacity can only be performed by very few technology businesses in Vietnam. Meanwhile, after tireless effort, the Calibration and Verification center of EMIN Vietnam is officially certified to be accredited by the ISO 17025 standard (Jan, 2021)

If you want your instruments calibrated, please contact:

Equipment Verification - Calibration - Repair Service Center - EMIN Vietnam JSC

Address: No 203 Nguyen Ngoc Vu Street, Trung Hoa Ward, Cau Giay District, Ha Noi City

Email: services@emin.vn - Hotline: 0968.060.220

Further information about digimatic calibration service can be found here.

相关新闻

2026年11月14日 11時35分16秒

What Is Fiber Polarity and How Do You Choose an MPO Method?

Fiber polarity ensures the transmit path connects to the corresponding receive path. For MPO-based duplex channels, the selected method must remain consistent across trunks, cassettes, adapters, and patch cords.

2026年11月14日 10時28分19秒

The scent of new wood in a newly handed-over apartment: How to measure and address formaldehyde (HCHO) levels before moving in

Many people refer to the pungent, acrid odor that emerges when opening a new cabinet as the "smell of new wood," assuming it will simply dissipate after a few days. In reality, however, what is being released could well be formaldehyde—a substance originating from the adhesives used in the pressed-wood panels—and our sense of smell is not a reliable enough gauge to determine the concentration levels present

2026年11月13日 17時23分39秒

Guide to Selecting a TCLP Toxicity Characteristic Leaching Procedure Shaker Configuration in Compliance with QCVN 07:2025/BNNMT and TCVN 9239:2012

Regulation QCVN 07:2025/BNNMT (replacing QCVN 07:2009/BTNMT and QCVN 50:2013/BTNMT) specifies hazardous waste and sludge thresholds based on leachate concentrations. To ensure that analytical results for heavy metals and organic compounds are accepted during ISO/IEC 17025 or VIMCERTS assessments, laboratories must comply with the Toxicity Characteristic Leaching Procedure (TCLP) specified in TCVN 9239:2012, which is equivalent to US EPA Method 1311

2026年11月13日 16時11分22秒

Checking the Temperature of Paint and Coating Surfaces After Curing Using an Infrared Thermometer

An infrared thermometer allows surface temperature measurement without direct contact, making it suitable for products coming out of curing ovens or surfaces that are difficult to access. However, to ensure reliable results for production quality control, it is important to understand the measurement principle and the factors that affect measurements on painted and coated surfaces.

2026年11月13日 15時07分40秒

Crowded Gyms and Yoga Studios: How to Manage Air Quality to Retain Members

Around 6 or 7 in the evening, the gym becomes packed; the music drowns out the sound of heavy breathing, and the air conditioning runs at full blast behind closed doors. At first glance, everything seems fine: the room is cool, the lights are bright, and the equipment is state-of-the-art. Yet, after just a few sessions, regular members begin to feel a heavy-headedness and find themselves running out of breath more quickly eventually, they simply stop renewing their memberships. No one complains about the personal trainers or the exercise machines. The very thing that makes them feel stifled and drives them away is something entirely invisible: the air inside the room