REPLICA TAPE READER DeFelsko PosiTector RTRH1 膜层厚度计(20至115μm)

- Measurement Range: 20 to 115 μm (0.8 to 4.5 mils)

- Accuracy (H):+ 5 μm (+ 0.2 mils)

- Resolution: + 1 μm (+ 0.2 mils)

- Anvil Diameter: Ø6.3 mm (Ø0.25 inch)

- Anvil Pressure: 110 grams-force (1.1 Newtons)

- Monochrome display with transflective technology enhances sunlight readability

- Storage of 250 readings—stored readings can be viewed or downloaded

- Size: 137 x 61 x 28 mm (5.4" x 2.4" x 1.1")

- WEIGHT: 140 g (4.9 oz.) without batteries

complete with Standard: with body and probe, stainless steel burnishing tool, cleaning cards(5), check shim, surface cleaning putty, protective rubber holster with belt clip, wrist strap, 3 AAA alkaline batteries, instructions, nylon carrying case with shoulder strap, protective lens shield, Long Form Certificate of Calibration traceable to NIST, USB cable, PosiSoft.net account

Detail

Literature

Manual

Quick Guide

HOW IT WORKS

   


1. Prepare the test surface
2. Burnish the Testex™ Press-O-Film™ replica tape
3. Prepare the PosiTector RTR
4. Measure

 

Prepare the test surface

Locate a representative site for measurement. Clean the surface to be tested.

DeFelsko recommends the use of cleaning putty to remove dust, debris, or residual blast media from the surface.

Firmly press the putty onto the surface using your fingers, and remove.

 

Burnish the replica tape (create a replica)

Select the appropriate grade of replica tape based on the target profile (Coarse or X-Coarse). See tape instructions for assistance.

Pull a single adhesive-backed replica tape free of its release paper. A “bule eye” circle of paper should remain on the release paper (it is not used for measurement).

Apply replica tape to blasted surface. Press the adhesive-backed ends of the paper to hold it firmly in place during the burnishing process.

Firmly compress replica film using the rounded end of the included stainless steel burnishing tool. Apply sufficient pressure in a circular and x-y rubbing motion to produce a replica with a uniform pebble grain appearance. It normally takes 30 to 60 seconds to fully compress all parts of the film on most surfaces. In general, too much compression is safer than too little.

After burnishing is complete, remove the replica tape from the surface.

Prepare the PosiTector RTR

Clean the measurement surfaces (anvils) using the included cleaning card. Swipe the card through the opening a few times while firmly pressing both probe buttons to remove dust particles and residual tape adhesive.

Power-up the PosiTector RTR by pressing the center navigation button. An image appears indicating that the probe requires zeroing.

Simultaneously press and hold both probe buttons firmly until the Gage beeps and the arrows point outward. Do not place anything in the measurement opening during this procedure.

Measure the included check shim to verify accuracy.

Ensure the correct grade of replica tape, C or XC, is displayed in the upper left corner of the LCD.

Measure

Insert the burnished replica tape into the measurement opening. Ensure the tape is properly positioned so that the burnished region is centered within the opening in the probe with the adhesive (sticky) side down.

To position the tape, move the Testex™ Press-O-Film™ replica tape to the back of the probe and align the two dots (printed on replica tape) with arrows on both sides of the measurement opening.

If you are using older Testex™ Press-O-Film™ replica tape that does not have the printed dots, simply align by centering the tape within the measurement opening.

Once positioned, firmly press both probe buttons simultaneously and hold until the PosiTector RTR beeps and the measurement is displayed. During measurement, a constant anvil pressure is applied to the replica tape regardless of how hard the two buttons are pressed.

The PosiTector RTR automatically subtracts the 50.8 μm (2 mil) of incompressible polyester film. No further adjustments are required.

REPLICA TAPE READER - Digital Spring Micrometer

   
PosiTector RTR Replica Tape Reader - Digital spring micrometer measures and records peak to valley surface profile height using replica tape.

  Simple

  • One-handed menu navigation
  • RESET feature instantly restores factory settings
  • Automatically subtracts the 50.8 μm (2 mil) incompressible substrate from all readings
  • Minimizes inspector workload by reducing the number of replicas needed to ensure accuracy

  Durable

  • Solvent, acid, oil, water and dust resistant – weatherproof
  • Rugged indoor/outdoor instrument – ideal for field or shop use
  • Shock-absorbing, protective rubber holster with belt clip
  • Two (2) year warranty on body AND probe

  Accurate

  • Measures height (H) and linearized height (HL)
  • Certificate of Calibration (Long Form) showing traceability to NIST included
  • Check Shim provided to verify accuracy
  • Conforms to national and international standards including ISO and ASTM

  Versatile

    • PosiTector body accepts all PosiTector RTR, SPG, 6000, 200, DPM, and UTG probes easily converting from a coating thickness gage to a dew point meter, surface profile gage or wall thickness gage [View Video]


  • Mils/Microns switchable
  • Selectable display languages
  • High contrast backlit display for bright or dark environments
  • Flip display enables right-side-up viewing
  • Uses alkaline or rechargeable batteries (built-in charger)

  Powerful

  • Continually displays/updates average, standard deviation, min/max height and number of readings
  • USB port for fast, simple connection to a PC and to supply continuous power. USB cable included
  • PosiSoft solutions for viewing, analyzing & reporting data:
    • PosiSoft USB Drive -stored readings and graphs can be accessed using universal PC/ Mac web browsers or file explorers. No software required
    • PosiSoft.net account - a free web-based application offering secure storage of thickness readings
    • PosiSoft 3.0 - desktop software (PC/Mac) for downloading, viewing, printing and storing measurement data. Available as a free download.
    • PosiSoft Mobile -(Advanced models only) - access readings, graphs, capture photos and update notations through WiFi enabled devices such as tablets, smart phones and computers
  • Screen Capture - record and save image into USB flash memory for record keeping and review
  • Every stored measurement is date and time stamped
  • Software updates via web keep your gage current

 

 

 

Testex Press-o-Film Replica Tape
For use with Testex Press-O-Film™ Replica Tape

 

Digital Spring Micrometer
Digital spring micrometer measures
and records peak to valley surface profile
height using replica tape

 


WiFi on PosiTector Advanced
models to wirelessly synchronize with PosiSoft.net, download software updates, and connect to mobile devices for expanded functionality
Learn More

 


PosiTector Inspection Kits:
Includes PosiTector body and your choice of probes: 6000 coating thickness probe, SPG and RTR surface profile probes, and DPM environmental probe in a hardshell case.

 

Download cataloge

Download Manual

 

  • 质量承诺
  • 正品保修
  • 送货到家
  • 交易简单化