Warranty policy

During using if there is any problems or errors that users can contact directly with Company Service Center or Customer Care Unit of the company for assistance.

EMIN Viet Nam Joint Stock Company

Warranty Policy

During using if there is any problems or errors that users can contact directly with Company Service Center or Customer Care Unit of the company for assistance.

I- Warranty

*Warranty Period: This is the time that EMIN is responsible for receiving and solving the warranty for the products provided by EMIN, which was on the warranty card and stamp.

* Valid warranty card: Is the warranty card issued by EMIN and provided with the product that was stamped by EMIN.

The warranty card is issued by EMIN and attached with the product stamped by EMIN, the warranty form must be in specified form, not separated – not pieced, production code on the warranty card must be the same as the code of product that need warranty (no signs of being erased or repaired)

* Valid warranty stamp: This is a sticker that EMIN paste on each product, no patchwork or no repairing, peeling, re-pasting.

II-General policy

EMIN applies the warranty policy nationally incuding customers who purchase EMIN products at any EMIN branch/office.

Product warranty : Overcoming defects, technical breakdown which occurs due to manufacturer's fault.

III. What is covered?

- Products are guaranteed with free charge in warranty period from the date of delivery (The warranty period is shown on the warranty card and according to the manufacturer's regulations for all technical incidents).

- With EMIN warranty card and and stamp on the product.

- Products are renewed: Products must meet the above warranty conditions and defects caused by manufacturer production that EMIN cannot repair will be changed by a new one.

IV- What is not covered?

- The product has expired on the warranty card or the warranty card lost.

- Warranty seals are torn, broken, overpasted or information modified.

- Warranty card does not specify the serial number and date of purchase.

- The number on the machine can not be identified or wrong than the number is recorded on the warranty card.

- The product is damaged due to mechanical deformation, damage due to human causes such as dropping, broking, impacting, scratching, distortion, moisture, leaking, flowing or fire, natural disaster, electric shock, and explosion.

- The product with signs of damage caused by rodents or insects.

- The product is used improperly, using wrong voltage regulation.

- Unauthorized dismantling, repairing by individuals or technicians who are not authorized before warranty claiming.

V-Service after warranty

Devices and products purchased from has expired or under non-guaranteed conditions will be repaired by EMIN Service Center at preferential prices or supported for repairing at EMIN.

VI- Location of warranty

SERVICE CENTER

Phone: (024) 353.812 .69 - Fax: (024) 351.90 3.60 - Email: hn@emin.vn

Website: http://www.emin.vn

Support time: 8h00 - 17h30 except Saturday, Sunday, holidays.

GENERAL DIRECTOR

관련 뉴스

2026년 10월 24일 09시 59분 14초

SiC/GaN Semiconductor Material Trends: From Materials Research to In-Depth Failure Analysis

As we enter the 2026–2030 period, wide-bandgap (WBG) semiconductor materials such as Silicon Carbide (SiC) and Gallium Nitride (GaN) are transforming the power electronics, electric vehicle (EV/HEV), renewable energy, and AI data center industries. The shift from traditional silicon to SiC and GaN enables higher power density, smaller passive components, and improved overall system energy efficiency.

2026년 10월 23일 15시 26분 05초

Chauvin Arnoux C.A 6117 Multifunction Electrical Installation Tester

An all-in-one testing solution that complies with the international standard IEC 60364-6. It features a 5.7-inch color graphical display, supports Type B RCD testing, includes memory for 1,000 measurements, and is equipped with a Lithium-ion battery providing 30 hours of continuous operation

2026년 10월 22일 11시 05분 06초

How Surface Gloss Affects the Perception of Color Intensity, And How to Measure It Accurately

Deciphering optical phenomena such as specular and diffuse reflection, distinguishing between SCI and SCE measurement modes, and providing guidance on using a combined colorimeter and glossmeter to accurately isolate color defects from surface gloss defects

2026년 10월 21일 15시 30분 17초

Plastic Products with Color Streaks: How to Adjust Back Pressure and Screw Speed? How Should Color Be Measured to Verify Proper Adjustment?

In the middle of the night shift, a batch of light-gray plastic emerged, streaked with debris. The machine operator took one look and did what came most naturally: he cranked up the screw speed and increased the back pressure to ensure the orange-colored pellets melted completely. By morning, the color was indeed more uniform. A few weeks later, the customer returned the entire shipment the products had become brittle, cracking at the slightest impact, and the color varied from one delivery to the next, failing to match the approved standard

2026년 10월 20일 16시 35분 05초

Controlling Color in Injection-Molded Products Using a Colorimeter: How to Correctly Interpret Delta E Values

Diagnosing the causes of plastic color variation, managing metamerism, distinguishing between SCI/SCE measurement modes, and applying Delta E standards for color deviation assessment in QA/QC