For full functionality of this site it is necessary to enable JavaScript.
EMIN.VN
0

When to test breakdown voltage? Practical experience from lab to factory

2025年11月13日 08時49分15秒

Breakdown voltage represents the limit to which a material can maintain its insulating ability before a discharge occurs. When this value is reduced, the insulation has lost its stability and there is a risk of short circuit, leakage or equipment failure.

Early inspection helps identify the level of aging, manufacturing deviations or environmental influences, especially in parts working in conditions of heat, humidity, or high electrical loads.

The most obvious practical situations when measuring breakdown voltage

- Production: evaluation of input materials, inspection of components after assembly and before shipment.

- Research: determination of dielectric properties of new materials, comparison of results before and after environmental tests.

- Equipment maintenance: inspection of insulation condition of motors, transformers, capacitors, switching devices or old cables.

Common errors and how to fix them

This measurement is prone to error if not performed correctly. Off-center electrode alignment causes uneven field distribution, leading to premature discharge. Poor grounding of the cable or a humid test environment can cause leakage currents on the surface of the sample. Contaminated or greasy samples can also give lower results than the actual results.

The solution lies in controlling the test conditions: keeping the surface dry and clean, adjusting the electrode gap to a stable level, choosing a consistent voltage ramp rate. In addition, the device needs to be periodically calibrated, because errors in the high-voltage measuring circuit can make the entire result invalid.

Read more about breakdown voltage to understand better: If you don't know about breakdown voltage then here is the answer for you.

When to repeat the measurement. Reasonable inspection schedule

Not all materials require frequent testing, but when operating conditions are severe, it is advisable to establish a clear inspection cycle. For production lines, batch testing is common, with each batch representing a shift or batch of material. For equipment operating continuously, re-testing is usually performed after each maintenance period or when abnormalities such as leaks, sparks, or changes in surface temperature are detected.

The results of each measurement should be recorded to monitor the decreasing trend of the breakdown voltage. When the value is found to be decreasing rapidly, it is the basis for assessing the aging level and planning for replacement before a failure occurs. 

Breakdown voltage testing is not a mandatory operation in every process, but is a key step in understanding the insulation condition of electrical materials and equipment. When the measurement data is collected and managed properly, it becomes the basis for maintaining the safety and reliability of the entire electrical system.

関連ニュース

SMEMA standard for PCB conveyors
2026年11月16日 14時00分39秒

SMEMA was developed to address this specific point; consequently, conveyors, loaders, and unloaders all include an SMEMA port in their technical specifications

Reduce scratches and drops of PCB boards during transfer between stages in an SMT production line
2026年11月16日 10時42分38秒

In a well-functioning SMT line, when QC detects defects at the end of the process, the immediate assumption is often that the issue lies with the solder paste printer or the component placement machine. However, upon closer investigation, there are certain types of defects that cannot be attributed to any single specific stage. Read the article below to learn more!

Homes on busy streets: How to measure fine particulate matter and exhaust fumes entering your living room
2026年11月16日 09時42分31秒

Living in a house facing a main road is particularly frustrating: you might wipe the tables until they’re spotless in the morning, only to find them covered in a layer of dust by the afternoon. Even with the doors tightly shut and the curtains drawn, the house still feels stuffy by evening—permeated by the faint, lingering presence of vehicle exhaust. While regular dust can be swept away, fine particulate matter the kind you can’t even see silently seeps in through the gaps around your doors and windows. So, before you rush to spend money on an air purifier or weather-stripping, take a moment to check the current air quality inside your home and identify exactly where the pollutants are entering

Can Laser Welding Machines Weld Aluminum Effectively ?
2026年11月16日 08時54分12秒

Laser welding is presented as an aluminum-joining method that concentrates heat at the weld point, helping limit distortion. Suitable settings depend on material thickness, filler wire use, and trial weld results.

What Gas Does a Plasma Cutter Use and How Do You Choose It?
2026年11月16日 08時53分20秒

Plasma cutting gas selection depends on the material, thickness, cut quality target, and operating cost. Clean air is economical, oxygen suits carbon steel, and nitrogen or argon-hydrogen supports stainless steel and aluminum applications.

お得な情報を受け取る

数量割引、まとめ買い価格の更新、新製品情報をメールでお届けします。

登録することで、当社の利用規約およびプライバシーポリシーに同意したものとみなされます。

クイックサポート

認定専門家へ直接アクセス